Fuji Electric FRENIC-Ace series - Page 774

Appendix G Conformity with Standards
Appendix-34
Compliance with the low voltage directive in the EU (Continued)
3. When used with the inverter, a molded case circuit breaker (MCCB), residual-current-operated protective
device (RCD)/earth leakage circuit breaker (ELCB) or magnetic contactor (MC) should conform to the EN or
IEC standards.
4. When you use a residual-current-operated protective device (RCD)/earth leakage circuit breaker (ELCB) for
protection from electric shock in direct or indirect contact power lines or nodes, be sure to install type B of
RCD/ELCB on the input (primary) of the inverter.
Note: A box (■) in the above table replaces S (Basic type) or E (EMC filter built-in type) depending on the
enclosure.
A box () in th
e above table replaces GA, GB or C depending on the model.
Power supply
voltage
Nominal applied motor
(kW)
Inverter type
ND/HD/HND
mode
MCCB or RCD/ELCB *1
Rated current
W/DCR W/o DCR
Three-phase 200 V
0.1
FRN0001E2■-2
HHD
5
5
0.2 HND 5 5
0.2
FRN0002E2■-2
HHD
5
5
0.4 HND 5 5
0.4
FRN0004E2■-2
HHD
5
5
0.75 HND 5 10
0.75
FRN0006E2■-2
HHD
5
10
1.1 HND 10 10
1.5
FRN0010E2■-2
HHD
10
15
2.2 HND 10 20
2.2
FRN0012E2■-2
HHD
10
20
3.0 ND 20 30
3.7
FRN0020E2■-2
HHD
20
30
5.5 ND 30 40
5.5
FRN0030E2■-2
HHD
30
50
7.5 HND 40 75
7.5
FRN0040E2■-2
HHD
40
75
11 HND 50 100
11
FRN0056E2■-2
HHD
50
100
15 HND 75 125
15
FRN0069E2■-2
HHD
75
125
18.5 HND 100 150
18.5
FRN0088E2■-2
HHD
100
150
22 HND 100 175
22
FRN0115E2■-2
HHD
100
175
30 HND 150 200
Three-phase 400 V
0.4
FRN0002E2■-4
HHD
5
5
0.75 HND 5 5
0.75
HD
5
5
0.75 ND 5 5
1.5
FRN0004E2■-4
HHD
5
5
1.1 HND 5 5
1.1
HD
5
5
0.75 ND 5 5
1.5
FRN0006E2■-4
HHD
5
10
2.2 HND 5 10
2.2
HD
5
10
2.2 ND 5 10
2.2
FRN0007E2■-4
HHD
10
15
- - - -
3.0
HD
10
15
3.0 ND 10 15
3.7
FRN0012E2■-4
HHD
10
20
- - - -
5.5
HD
15
30
5.5 ND 15 30