Fuji Electric Frenic Mega Series - Page 200

5.2 Function Code Tables
5-19
Chapter 5 Function Code
Function
Code Tables
F codes
E codes
C codes
P codes
H codes
A codes
b codes
r codes
J codes
d codes
U codes
y codes
Drive control
Code Name Data setting range
Change
when
running
Data
copying
Default
setting
V/f
PG
V/f
w/o
PG
w/
PG
To rq ue
control
Refer to
 page:
r
04 Maximum Output Voltage 4 80 to 240 V: Output an AVR-controlled voltage
(for 200 V class series)
160 to 500 V: Output an AVR-controlled voltage
(for 400 V class series)
N Y2 200
400
Y Y N N Y ―
r
05 Torque Boost 4 0.0% to 20.0% (percentage with respect to Rated Voltage at Base
Frequency 4)
Y Y *2 Y Y N N N
r
06 Electronic Thermal Overload
Protection for Motor 4 (Select motor
characteristics)
1: Enable (For a general-purpose motor with shaft-driven cooling fan)
2: Enable (For an inverter (FV)-driven motor with separately powered
cooling fan)
Y Y 1 Y Y Y Y Y
r
07 (Operation level) 0.00 (Disable), 1% to 135% of the rated current of the inverter Y Y1, Y2 *3 Y Y Y Y Y
r
08 (Thermal time constant) 0.5 to 75.0 min Y Y *4 Y Y Y Y Y
r
09 DC Braking 4
(Braking starting frequency)
0.0 to 60.0 Hz Y Y 0.0 Y Y Y Y N
r
10 (Operation level) 0% to 100% (HD mode), 0% to 80% (MD/LD mode) Y Y 0 Y Y Y Y N
r
11 (Braking time) 0.00 (Disable): 0.01 to 30.00 s Y Y 0.00 Y Y Y Y N
r
12 Starting Frequency 4 0.0 to 60.0 Hz Y Y 0.5 Y Y Y Y N
r
13 Load Selection/
Auto Torque Boost/
Auto Energy Saving Operation 4
0: Variable torque load
1: Constant torque load
2: Auto torque boost
3: Auto-energy saving operation (Variable torque load during
ACC/DEC)
4: Auto-energy saving operation (Constant torque load during
ACC/DEC)
5: Auto-energy saving operation (Auto-torque boost during ACC/DEC)
N Y 1 Y Y N Y N
r
14 Drive Control Selection 4 0: V/f control with slip compensation inactive
1: Dynamic torque vector control
2: V/f control with slip compensation active
3: V/f control with speed sensor
4: Dynamic torque vector control with speed sensor
5: Vector control without speed sensor
6: Vector control with speed sensor
N Y 0 Y Y Y Y Y
r
15 Motor 4 (No. of poles) 2 to 22 poles N Y1, Y2 4 Y Y Y Y Y
r
16 (Rated capacity) 0.01 to 1000 kW (when r39 = 0 or 2 to 4)
0.01 to 1000 HP (when r39 = 1)
N Y1, Y2 *6 Y Y Y Y Y
r
17 (Rated current) 0.00 to 2000 A N Y1, Y2 *6 Y Y Y Y Y
r
18 (Auto-tuning) 0: Disable
1: Tune while the motor stops. (%R1, %X and rated slip frequency)
2: Tune while the motor is rotating under V/f control (%R1, %X, rated
slip frequency, no-load current, magnetic saturation factors 1 to 5,
and magnetic saturation extension factors "a" to "c")
3: Tune while the motor is rotating under vector control (%R1, %X,
rated slip frequency, no-load current, magnetic saturation factors 1
to 5, and magnetic saturation extension factors "a" to "c." Available
when the vector control is enabled.)
N N 0 Y Y Y Y Y
r
19 (Online tuning) 0: Disable 1: Enable Y Y 0 Y N N N N
r
20 (No-load current) 0.00 to 2000 A N Y1, Y2 *6 Y Y Y Y Y
r
21 (%R1) 0.00 to 50.00% Y Y1, Y2 *6 Y Y Y Y Y
r
22 (%X) 0.00 to 50.00% Y Y1, Y2 *6 Y Y Y Y Y
r
23 (Slip compensation gain for driving) 0.0 to 200.0% Y* Y 100.0 Y Y Y Y N
r
24 (Slip compensation response time) 0.01 to 10.00 s Y Y1, Y2 0.12 Y Y N N N
r
25 (Slip compensation gain for braking) 0.0 to 200.0% Y* Y 100.0 Y Y Y Y N
r
26 (Rated slip frequency) 0.00 to 15.00 Hz N Y1, Y2 *6 Y Y Y Y N
r
27 (Iron loss factor 1) 0.00 to 20.00% Y Y1, Y2 *6 Y Y Y Y Y
r
28 (Iron loss factor 2) 0.00 to 20.00% Y Y1, Y2 0.00 Y Y Y Y Y
r
29 (Iron loss factor 3) 0.00 to 20.00% Y Y1, Y2 0.00 Y Y Y Y Y
r
30 (Magnetic saturation factor 1) 0.0 to 300.0% Y Y1, Y2 *6 Y Y Y Y Y
r
31 (Magnetic saturation factor 2) 0.0 to 300.0% Y Y1, Y2 *6 Y Y Y Y Y
r
32 (Magnetic saturation factor 3) 0.0 to 300.0% Y Y1, Y2 *6 Y Y Y Y Y
r
33 (Magnetic saturation factor 4) 0.0 to 300.0% Y Y1, Y2 *6 Y Y Y Y Y
r
34 (Magnetic saturation factor 5) 0.0 to 300.0% Y Y1, Y2 *6 Y Y Y Y Y
r
35 (Magnetic saturation extension factor 0.0 to 300.0% Y Y1, Y2 *6 Y Y Y Y Y
r
36 (Magnetic saturation extension factor 0.0 to 300.0% Y Y1, Y2 *6 Y Y Y Y Y
r
37 (Magnetic saturation extension factor 0.0 to 300.0% Y Y1, Y2 *6 Y Y Y Y Y
r
39 Motor 4 Selection 0: Motor characteristics 0 (Fuji standard motors, 8-series)
1: Motor characteristics 1 (HP rating motors)
2: Motor characteristics 2 (Fuji motors exclusively designed for vector
control)
3: Motor characteristics 3 (Fuji standard motors, 6-series)
4: Other motors
N Y1, Y2 0 Y Y Y Y Y
r
40 Slip Compensation 4
(Operating conditions)
0: Enable during ACC/DEC and at base frequency or above
1: Disable during ACC/DEC and enable at base frequency or above
2: Enable during ACC/DEC and disable at base frequency or above
3: Disable during ACC/DEC and at base frequency or above
N Y 0 Y Y N N N
r
41 Current Fluctuation Damping Gain
for Motor 4
0.00 to 0.40 Y Y 0.20 Y Y N N N
r
42 Motor/Parameter Switching 4
(Mode selection)
0: Motor (Switch to the 4th motor)
1: Parameter (Switch to r codes)
N Y 0 Y Y Y Y Y 5-211
*2 The factory default differs depending upon the inverter's capacity. See Table 5.2-17.
*3 The motor rated current is automatically set. See Table 5.2-18 (function code P03).
*4 5.0 min for inverters with a capacity of 22 kW or below; 10.0 min for those with 30 kW or above
*6 The motor parameters are automatically set, depending upon the inverter's capacity. See Table 5.2-18.