Fuji Electric Frenic-Mini - Page 126

5-45
 If P99 (Motor selection) is set to 0 (Fuji standard 8-series motors), 3 (Fuji standard 6-series
motors), or 4 (Other motors):
Rated current (A)
If P99 (Motor selection) is set to:
Setting
range
(kW)
0 3 4
Shipping destination
(Version)
Shipping destination
(Version)
Shipping destination
(Version)
Power
supply
voltage
Function
code
P02
Nomi-
nal
applied
motor
(kW)
Asia EU Japan Asia EU Japan Asia EU Japan
0.01 to 0.06 0.06 0.40 0.44 0.38 0.40 0.44 0.38 0.40 0.44 0.38
0.07 to 0.10 0.1 0.62 0.68 0.61 0.62 0.68 0.61 0.62 0.68 0.61
0.11 to 0.20 0.2 1.18 1.30 1.16 1.19 1.30 1.18 1.18 1.30 1.16
0.21 to 0.40 0.4 2.10 2.30 2.13 2.10 2.30 2.13 2.10 2.30 2.13
0.41 to 0.75 0.75 3.29 3.60 3.36 3.29 3.60 3.36 3.29 3.60 3.36
0.76 to 1.50 1.5 5.55 6.10 5.87 5.55 6.10 5.87 5.55 6.10 5.87
1.51 to 2.20 2.2 8.39 9.20 8.80 8.39 9.20 8.80 8.39 9.20 8.80
2.21 to 3.70 3.7 13.67 15.00 14.38 13.67 15.00 14.38 13.67 15.00 14.38
3.71 to 5.50 5.5 20.04 22.00 21.19 20.04 22.00 21.19 20.04 22.00 21.19
Three-phase 200 V
Single-phase 200 V Single-phase 100 V
5.51 to 10.00 7.5 26.41 29.00 28.17 26.41 29.00 28.17 26.41 29.00 28.17
0.01 to 0.06 0.06 0.19 0.22 0.19 0.19 0.22 0.19 0.19 0.22 0.19
0.07 to 0.10 0.1 0.31 0.34 0.31 0.31 0.34 0.31 0.31 0.34 0.31
0.11 to 0.20 0.2 0.58 0.65 0.58 0.59 0.65 0.59 0.58 0.65 0.58
0.21 to 0.40 0.4 1.09 1.15 1.07 1.09 1.15 1.07 1.09 1.15 1.07
0.41 to 0.75 0.75 1.71 1.80 1.68 1.71 1.80 1.68 1.71 1.80 1.68
0.76 to 1.50 1.5 3.04 3.05 2.94 3.04 3.05 2.94 3.04 3.05 2.94
1.51 to 2.20 2.2 4.54 4.60 4.40 4.54 4.60 4.40 4.54 4.60 4.40
2.21 to 3.70 3.7 7.43 7.50 7.20 7.43 7.50 7.20 7.43 7.50 7.20
3.71 to 5.50 5.5 10.97 11.00 10.59 10.97 11.00 10.59 10.97 11.00 10.59
Three-phase 400 V
5.51 to 10.00 7.5 14.63 14.50 14.08 14.63 14.50 14.08 14.63 14.50 14.08
NOTE: The above values in the "Rated current" column are exclusively applicable to the four-pole Fuji
standard motors rated for 200 V or 400 V at 60 Hz. If the base frequency, rated voltage, and the number of
poles are different, however, change the P03 data to the rated current printed on the nameplate.
Also when you use non-standard or other manufacturer’s motors, change the P03 data to the rated current
printed on the motor's nameplate.