– 7 –
6-3
PID Palette (Ch3)
Saves the palette values of PV and PID. Up to seven sets can be saved.
6-4
Ramp soak (Ch4)
Create a pattern of temperatures using ramp soak combinations. You can create a temperature
pattern with up to 16 steps.
"
db" (db) Dead band Shifts the cooling
proportional band
from the set value
-50 to 50% 0%
(Note4)
"bAL" (bAL) Output
convergence value
Offset value which
is added to the MV
output value
-100 to 100% 0/50
(single/
dual)
"
Ar" (Ar) Anti-reset
windup
Sets the range of
integration control
0 to 100% FS 100%FS
"
rEv" (rEv) Sets normal/
reverse operations
Sets the control
action
rv-- (heat (reverse)
/cool (none))
no-- (heat (normal)
/cool (none))
rvno (heat (reverse)
/cool (normal))
norv (heat (normal)
/cool (reverse))
rvrv (heat (reverse)
/cool (reverse))
nono (heat (normal)
/cool (normal))
rv--/rvno
(single/
dual)
"
SvL" (SvL) SV limit
(lower limit)
Sets the lower limit
of SV
0 to 100% FS 0% FS
(Note5)
"Svh" (Svh) SV limit
(upper limit)
Sets the upper
limit of SV
0 to 100% FS 100% FS
(Note5)
"t[1" (TC1) OUT1 proportion
cycle
Sets the proportion
cycle of the control
output (OUT1)
(contacts, SSR drive)
1 to 150 sec 30:
Contact
2: SSR
drive
(Note7)
"t[2" (TC2) OUT2 proportion
cycle
Sets the proportion
cycle of the control
output (OUT2)
(contacts, SSR drive)
1 to 150 sec 30:
Contact
2: SSR
drive
(Note4)
"Plc1" (PLC1)
OUT1 lower limit
Sets the lower limit
of the control output
(OUT1)
-3.0 to 103.0% -3.0%
"
Ph[1" (PhC1)
OUT1 upper limit
Sets the upper limit
of the control output
(OUT1)
-3.0 to 103.0% 103.0%
"
PL[2" (PLC2)
OUT2 lower limit
Sets the lower limit
of the control output
(OUT2)
-3.0 to 103.0% -3.0%
(Note4)
"Ph[2" (PhC2)
OUT2 upper limit
Sets the upper limit
of the control output
(OUT2)
-3.0 to 103.0% 103.0%
(Note4)
"P[UT" (PCUT) Selects the type of
output limiter
Sets the type of
output limiter
0 to 15 0
Parameter
display symbol
Parameter name Function Setting range
Initial
value.
Remarks
"Sv1" (Sv1) SV 1 Sets the SV set
value
SV limit (lower)
(SVL) to
SV limit (upper)
(SVH) %FS
0%FS
(Note5)
"P1" (P1) Proportional band 1 Sets the
proportional band
0.0 to 999.9% 5.0%
"
i1" (i1) Integration time 1 Sets the
integration time
0 to 3200 sec 240 sec
"
d1" (d1) Differential time 1 Sets the
differential time.
0.0 to 999.9 sec
60.0 sec
"hyS1" (hyS1) ON/OFF control
hysteresis 1
Sets the hysteresis
when using the
ON/OFF control.
0 to 50% FS 1 °C
"
[oL1" (CoL1) Cooling proportional
band 1
Sets the cooling
proportional band
0.0 to 100.0 1.0
(Note4)
"db1" (db1) Dead band 1 Sets the dead
band
-50.0 to 50.0% 0%
(Note4)
"bAL1" (bAL1)
Output convergence
value 1
Offset value which
is added to the
control output
-100.0 to 100.0% 0/50
(single/
dual)
"
Ar1" (Ar1) Anti-reset windup 1 Sets the anti-reset
windup
0 to 100% FS
100%FS
"rEv1" (rEv1) Sets normal/
reverse 1
Sets the control
action
rv-- (heat (reverse)/
cool (none))
no-- (heat (normal)/
cool (none))
rvno (heat (reverse)/
cool (normal))
norv (heat (normal)/
cool (reverse))
rvrv (heat (reverse)/
cool (reverse))
nono (heat (normal)/
cool (normal))
rv--/rvno
(single/
dual)
(Note6)
"Sv7" (Sv7) SV 7 Sets the SV set
value
SV limit (lower)
(SVL) to
SV limit (upper)
(SVH) %FS
0%FS
(Note5)
"P7" (P7)
Proportional band 7
Sets the
proportional band
0.0 to 999.9% 5.0%
"
i7" (i7) Integration time 7 Sets the
integration time
0 to 3200 sec 240 sec
"
d7" (d7) Differential time 7 Sets the
differential time.
0.0 to 999.9 sec
60.0 sec
"hyS7" (hyS7) ON/OFF control
hysteresis 7
Sets the hysteresis
when using the
ON/OFF control.
0 to 50% FS 1 °C
"
[oL7" (CoL7)
Cooling proportional
band 7
Sets the cooling
proportional band
0.0 to 100.0 1.0
(Note4)
Parameter
display symbol
Parameter name Function Setting range
Initial
value
Remarks
RST
RST
…
…
…
…
…
…
"db7" (db7) Dead band 7 Sets the dead
band
-50.0 to 50.0% 0%
(Note4)
"bAL7" (bAL7)
Output convergence
value 7
Offset value which
is added to the
control output
-100.0 to 100.0% 0/50
(single/
dual)
"
Ar7" (Ar7)
Anti-reset windup 7
Sets the anti-reset
windup
0 to 100% FS
100% FS
"rEv7" (rEv7) Sets normal/reverse
7
Sets the control
action
rv-- (heat (reverse)
/cool (none))
no--(heat (normal)
/cool (none))
rvno (heat (reverse)
/cool (normal))
norv (heat (normal)
/cool (reverse))
rvrv (heat (reverse)
/cool (reverse))
nono (heat (normal)
/cool (normal))
rv--/rvno
(single/
dual)
(Note6)
"SvMX" (SvMX) Sets the Max SV
selection number
Choosing SV with
the user key sets it
to the maximum
possible number.
Sv0
Sv1
Sv2
Sv3
Sv4
Sv5
Sv6
Sv7
di
Sv7
"
PL1m" (PL1M) Set the Max PID
selection number
Choosing PID with
the user key sets it
to the maximum
possible number.
Pid0
Pid1
Pid2
Pid3
Pid4
Pid5
Pid6
Pid7
di
P
id
7
Parameter
display symbol
Parameter name Function Setting range
Initial
value
Remarks
"
Ptn
" (PTn) Ramp soak
operation pattern
(Step No.)
Sets which
steps to use in
the ramp soak
operation
pattern
0 (uses steps 1 to 4)
1 (uses steps 5 to 8)
2 (uses steps 1 to 8)
3 (uses steps 9 to 12)
4 (uses steps 13 to 16)
5 (uses steps 9 to 16)
6 (uses steps 1 to 16)
di (according to di)
6
(Note 21)
"
TiMU
" (TiMU) Ramp soak time
units
Sets the units
of the ramp
soak time
hh.MM (hour:min)
MM.SS (min:sec)
hh.MM
"
Sv-1
"
(Sv-1)
Ramp soak 1 seg/
SV
Sets the SV
0 to 100% FS 0%FS
"
tm1r
" (TM1r) Ramp soak 1 seg
ramp time
Sets the ramp
time
00.00 to 99.59 (hour:min/
min:sec)
00:00
(hour:min)
"
tm1S
" (TM1S) Ramp soak 1 seg
soak time
Sets the soak
time
00.00 to 99.59 (hour:min/
min:sec)
00:00
(hour:min)
"
Sv16
"
(Sv16)
Ramp soak 16 seg/
SV
Sets the SV
0 to 100% FS 0%FS
"
t16r"
(T16r")
Ramp soak 16
seg ramp time
Sets the ramp
time
00.00 to 99.59 (hour:min/
min:sec)
00:00
(hour:min)
"t16S" (T16S) Ramp soak 16
seg soak time
Sets the soak
time
00.00 to 99.59 (hour:min/
min:sec)
00:00
(hour:min)
"mod" (Mod)
Ramp soak mode
Sets the
program
operation
method
0 to 15 0
"
Gsok" (Gsok) Guaranty soak
ON/OFF
Sets the
guaranty soak
ON or OFF
oFF (guaranty soak off)
on (guaranty soak on)
oFF
"
GS-L"(GS-L) Guaranty soak
band (lower)
Sets the lower
limit of guaranty
soak
0 to 50% FS 5°C
"
GS-h"(GS-h) Guaranty soak
band (upper)
Sets the upper
limit of guaranty
soak
0 to 50% FS 5°C
"PvST"
(
PvST) PV start Sets whether or
not to start
ramp soak with
PV.
oFF (PV start OFF)
on (PV start ON)
oFF
"
ConT
"(ConT) Restore mode Sets how to
restart when
the controller is
restored after a
power loss.
rES (Reset)
Con (Continue)
ini (Restart)
rES
(Note 20)
"
PTnM
" (PTnM) Sets the Max
pattern selection
Choosing
pattern with the
user key sets it
to the
maximum
possible
number.
0 to 6,di 6
"
PMin
"(PMin) Sets the Min
pattern selection
Choosing
pattern with the
user key sets it
to the minimum
possible
number.
0 to 6, di 0
Parameter
display symbol
Parameter name Function Setting range
Initial
value.
Remarks
RST
…
…
…
…
…
…
RST
To Next Page
Loading...
