EasyManua.ls Logo

Fujitsu PRIMERGY RX100 S7 - Page 26

Fujitsu PRIMERGY RX100 S7
490 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Upgrade and Maintenance Manual
RX100 S7
Contents
16.10.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 425
16.10.3 Removing the riser module 2 . . . . . . . . . . . . . . . . . . 426
16.10.4 Disconnecting the defective BBU cable from the RAID
controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
16.10.5 Removing the BBU with the BBU holder . . . . . . . . . . . . 428
16.10.6 Removing the BBU from the BBU holder . . . . . . . . . . . . 429
16.10.7 Disconnecting the defective BBU cable from the BBU . . . . . 430
16.10.8 Connecting the new BBU cable to the BBU . . . . . . . . . . 430
16.10.9 Installing the BBU in the holder . . . . . . . . . . . . . . . . . 431
16.10.10 Installing the BBU with the BBU holder . . . . . . . . . . . . . 432
16.10.11 Connecting the new BBU cable to the RAID controller . . . . . 433
16.10.12 Installing the riser module 2 . . . . . . . . . . . . . . . . . . . 434
16.10.13 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 434
16.11 Replacing the RAID card cable . . . . . . . . . . . . . . . . 435
16.11.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 435
16.11.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 435
16.11.3 Removing the riser module 2 . . . . . . . . . . . . . . . . . . 436
16.11.4 Removing the defective RAID card cable . . . . . . . . . . . . 436
16.11.5 Installing the new RAID card cable . . . . . . . . . . . . . . . 438
16.11.6 Installing the riser module 2 . . . . . . . . . . . . . . . . . . . 439
16.11.7 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 440
16.12 Replacing the power cables (redundant PS) . . . . . . . . 440
16.12.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 440
16.12.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 440
16.12.3 Removing the defective power cable . . . . . . . . . . . . . . 441
16.12.4 Installing the new power cable . . . . . . . . . . . . . . . . . 442
16.12.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 442
17 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443
17.1 Mechanical overview . . . . . . . . . . . . . . . . . . . . . 443
17.1.1 Front side . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443
17.1.2 Rear side . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444
17.1.3 Top view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445
17.2 Connectors and indicators . . . . . . . . . . . . . . . . . . 447
17.2.1 System board . . . . . . . . . . . . . . . . . . . . . . . . . . 447
17.2.2 Connector panel . . . . . . . . . . . . . . . . . . . . . . . . 451
17.2.3 Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 453
17.2.3.1 Control elements . . . . . . . . . . . . . . . . . . . . . . 453
17.2.3.2 Indicators on the control panel . . . . . . . . . . . . . . . 455

Table of Contents

Other manuals for Fujitsu PRIMERGY RX100 S7

Related product manuals