RX600 S5 Operating Manual
Contents
7.5 No screen display or display drifts . . . . . . . . . . . . . . 87
7.6 Incorrect date and time . . . . . . . . . . . . . . . . . . . . 88
7.7 Drives reported as "dead" when starting system . . . . . . 88
7.8 Added drive reported as defective . . . . . . . . . . . . . . 89
7.9 Error message on screen . . . . . . . . . . . . . . . . . . . 89
8 CSS components . . . . . . . . . . . . . . . . . . . . . . . . 91
8.1 Hot-plug components . . . . . . . . . . . . . . . . . . . . . 93
8.1.1 Hot-plug power supply units . . . . . . . . . . . . . . . . . . . 93
8.1.1.1 Replacing a hot-plug power supply unit . . . . . . . . . . . 94
8.1.1.2 Adding a hot-plug power supply unit . . . . . . . . . . . . . 95
8.1.2 Hot-plug fans . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
8.1.2.1 Replacing a defective fan . . . . . . . . . . . . . . . . . . 98
8.1.2.2 Adding new fans . . . . . . . . . . . . . . . . . . . . . . . 99
8.1.3 Hot-plug HDD modules . . . . . . . . . . . . . . . . . . . . . 100
8.1.3.1 HDD/SSD module and dummy module . . . . . . . . . . . 102
8.1.3.2 Removing/installing the dummy module . . . . . . . . . . . 103
8.1.3.3 Installing the HDD module . . . . . . . . . . . . . . . . . . 104
8.1.3.4 Removing the HDD module . . . . . . . . . . . . . . . . . 105
8.1.4 Hot-plug expansion cards . . . . . . . . . . . . . . . . . . . . 107
8.1.4.1 Identifying the defective CSS component . . . . . . . . . . 109
8.1.4.2 Removing a hot-plug expansion card . . . . . . . . . . . . 109
8.1.4.3 Removing a dummy module . . . . . . . . . . . . . . . . . 112
8.1.4.4 Installing a hot-plug expansion card . . . . . . . . . . . . . 113
8.1.5 Hot-plug memory boards . . . . . . . . . . . . . . . . . . . . 115
8.1.5.1 Identifying the defective memory . . . . . . . . . . . . . . . 116
8.1.5.2 Removing the memory board in question . . . . . . . . . . 117
8.1.5.3 Removing a defective memory module . . . . . . . . . . . 117
8.1.5.4 Installing a new memory module . . . . . . . . . . . . . . . 119
8.1.5.5 Reinstalling the memory board in question . . . . . . . . . 119
8.1.5.6 Adding a memory board . . . . . . . . . . . . . . . . . . . 120
8.2 Non-hot-plug components . . . . . . . . . . . . . . . . . . . 121
8.2.1 Identifying the defective CSS component . . . . . . . . . . . . 122
8.2.2 Replacing a non-hot-plug expansion card . . . . . . . . . . . . 122
8.2.2.1 Removing a non-hot-plug expansion card . . . . . . . . . . 122
8.2.2.2 Installing a non-hot-plug expansion card . . . . . . . . . . . 125
8.2.3 Replacing SFP+ transceiver modules . . . . . . . . . . . . . . 126
8.2.3.1 Removing an SFP+ transceiver module . . . . . . . . . . . 126
To Next Page
Loading...
