Fujitsu UTY-RNRUZ5 - Summer Time Setting; Preference Settings

(7) (8)
Auto Off
Cancel OK
Enable/Disable [Disable]
Absence Detection Time [In 24 hr]
Fri 10:00AM
Enable/Disable
Cancel OK
Enable
Disable
When the [OK] is touched, the display returns to “Auto
O󰀨”screen.
(9) Touchthe[AbsenceDetectionTime]onthe“AutoO󰀨”
screen.
(10) The “Absence Detection Time” screen is displayed. Set the
time with [
] or [ ]. The time can be set from 1 to 24 hr.
(9) (10)
Auto Off
Cancel OK
Enable/Disable [Disable]
Absence Detection Time [In 24 hr]
Fri 10:00AM
Absence Detection Time
Cancel OK
In
hr
24
Fri 10:00AM
NOTE
When detection time the same as or shorter than “Auto
Saving”issetat“AutoO󰀨”,“AutoSaving”doesnotoperate.
When the [OK] is touched, the display returns to the “Auto
O󰀨”screen.Andwhenthe[OK]onthe“AutoO󰀨”screen
is touched, the display returns to the “Human Sensor
Setting” screen.
When the [Back] on the “Human Sensor Setting” is
touched, the display returns to the “Special Setting” screen.
3-5-7 FanControlforEnergySaving
(for administrator)
(1) Touch the [Fan Control for Energy Saving] on the “Special
Setting”screen.Whenthe“PasswordVerication”screen
is displayed, enter the password and touch the [OK].
(2) “Fan Control for Energy Saving” screen is displayed. Touch
the [Enable] on the “Fan Control for Energy Saving” screen.
(1) (2)
Back
Previous
Page
Page 2/ 2 Special Setting
Human Sensor
Setting
Emergency Heat
Fan Control for
Energy Saving
Away Setting
Fan Control for Energy Saving
Cancel OK
Enable
Disable
When the [OK] is touched, the display returns to the
“Special Setting” screen.
3-5-8 Emergency Heat
On/O󰀨ofEmergencyHeat
(1) Touch the [Emergency Heat] on the “Special Setting”
screen.
(2) “Emergency Heat” screen is displayed. Touch the [On]
or[O󰀨]onthe“EmergencyHeat”screen.
(1) (2)
Back
Previous
Page
Page 2/ 2 Special Setting
Human Sensor
Setting
Emergency Heat
Fan Control for
Energy Saving
Away Setting
Emergency Heat
Cancel OK
On
Off
When you touch the [OK], the data is transmitted to the
indoor unit, and then the display returns to “Special Set-
ting” screen.
3-6 SummerTime(DaylightSavingTime)
Setting (for administrator)
The time display and timer operation are 1 hour earlier than
usual.
(1) Touch the [Summer Time
Setting] on the “Main Menu”
screen.
Monitor
Previous
Page
Page 2/ 2 Main Menu
Summer Time
Setting
Initial Setting Maintenance
Preference
EnableorDisabletheSummerTimeSetting
(1) “Summer Time Setting” screen
is displayed. Select the [En-
able] or [Disable] on the “Sum-
mer Time Setting” screen.
Summer Time Setting
Cancel OK
Enable
Disable
When the [OK] is touched, after the setting change
screen is displayed, the display returns to the “Main
Menu” screen.
3-7 Preference (for administrator)
Settings of the Touch screen
(1) Touch the [Preference] on the “Main Menu” screen.
(2) “Preference” screen is displayed.
(1) (2)
Monitor
Previous
Page
Page 2/ 2 Main Menu
Summer Time
Setting
Initial Setting Maintenance
Preference
Back
Preference
Panel
Calibration
Backlight
Setting
Contrast
Thefollowingcontentsareset:
• PanelCalibration:
When the touched position and the corresponding
position does not match on the screen, perform this
setting.
• BacklightSetting:
Backlightenable/disable,brightness,ando󰀨timecan
be set.
• Contrast:
Adjusts the contrast of the screen.
When the item to be set is touched, the display switches
to each setting screen. When each setting is complete
or canceled, the display returns to this screen. When
[Back] is touched, the display returns to the “Main Menu”
screen.
En-16