Fujitsu UTY-RNRUZ5 - Temp. Unit Setting; R.C.group Name Setting; Sensor Setting; Password Setting

3-8-3 Temp.UnitSetting
(1) Touch the [Temp. Unit Setting] on the “Initial Setting”
screen.
(2) “Temp. Unit Setting” screen is displayed. Select the [°F]
or [°C]. (Factory setting is “°F”.)
(1) (2)
Back
Next
Page
Page 1/ 4 Initial Setting
Language Setting Date Setting
R.C.Group
Name Setting
Temp. Unit
Setting
°C
°C
°F
°F
Temp. Unit Setting
Cance
lO
K
When the [OK] is touched, after a setting change screen
is displayed, the display returns to the “Initial Setting”
screen.
3-8-4 R.C.GroupNameSetting
(1) Touch the [R.C.Group Name
Setting] on the “Initial Setting”
screen.
“R.C.Group Name Setting”
screen is displayed.
Back
Next
Page
Page 1/ 4 Initial Setting
Language Setting Date Setting
R.C.Group
Name Setting
Temp. Unit
Setting
Descriptionofthescreen
R.C.Group Name Setting
Cancel OK
Fixed
Phrase
UVW
XY
Z./
_–
ABC
DE
ABCDEFGHIJKLM
│O
ver
FGH
IJ
KLM
NO
0–9
SP BS
PQR
ST
(a)
(b)
(c)
(d)
(e)
(f)
(a) Inputarea:
When inputting more than 12 characters, “Over” is
shown at the right end.
(b) Characterkeys:
Touch the same key until the character to be used is dis-
played.
(c) FixedPhrasekey:
[Floor,Corridor,O󰀩ce,ConfRoom,ReceptRoom,
Room, Room No., Front, Side, Entrance, Outlet, East,
West, South, North, Window] is registered. Touch the
[Fixed Phase] key until the sentence to be used is dis-
played.
(d) Space key
(e) Backspace key
(f) Cursor keys
ChangetheR.C.GroupName
(2) Touch each key and enter the name. When the [OK] is
touched, after a setting change screen is displayed, the
display returns to the “Initial Setting” screen.
3-8-5 R.C. Sensor Setting
(1) Set the [R.C. Sensor Setting] on the “Initial Setting”
screen.
(2) “R.C. Sensor Setting” screen is displayed. Touch the
[Used].
(1) (2)
Back
Previous
Page
Page 2/ 4 Initial Setting
R.C. Sensor
Setting
Password Setting
Display Item
Setting
Master Indoor
Unit Setting
Next
Page
R.C. Sensor Setting
Cancel OK
Used
Not Used
NOTE
When set to [Not Used] by this setting, the following func-
tionscannotbeused:
• Custom Auto in the operation mode. Refer to [2 CON-
TROL]→[2-2OperationSettings]→[2-2-1Setthe
Operation Mode].
• AwaySetting.Referto[3-5SpecialSetting]→[3-5-5
Away Setting].
• Optimum Start Setting. Refer to [3-8-9 Optimum Start
Setting].
When the [OK] is touched, after the data is transmitted
to the indoor unit, the display returns to the “Initial Set-
ting” screen.
3-8-6 PasswordSetting
(1) Touch the [Password Setting]
on the “Initial Setting” screen.
Back
Previous
Page
Page 2/ 4 Initial Setting
R.C. Sensor
Setting
Password Setting
Display Item
Setting
Master Indoor
Unit Setting
Next
Page
ChangethePassword
(2) “Password Setting” screen is displayed. Touch the
[Change Password].
(3) “PasswordVerication”screenisdisplayed.Enterthe
current password, and touch the [OK].
(2) (3)
Password Setting
Change Password
Change Setting
Back
0
CL
5
1
6
2
7
3
8
4
9
Cancel OK
Password Verification
Enter Current Password
NOTE
The default password is “0000” (4 digits).
(4) If the password is entered cor-
rectly, the “Change Password”
screen is displayed.
0
CL
5
1
6
2
7
3
8
4
9
Cancel OK
Change Password
Enter New Password
When the new password is entered and the [OK] is
touched, after the setting change screen is displayed,
the display returns to the “Password Setting” screen.
En-20