Sensors and Accessories (Option)
The units are designed to match the
NavNet 3D series and other navigation
equipment. The
“
Plug and Play
”
system
utilizes CAN bus interface protocol, which
gives the system exceptional interface
ability.
The FI-50 Series utilize high-contrast, backlit LCD displays for
superior viewing even in direct sunlight. Each unit features an
easy-to-read display and 4 simple programming buttons for
operation. The function for each key and combination are printed
directly on the front panel.
The FI-50 series of instruments minimize power consumption
by turning off the backlight during the daytime. Sensors on
the front panel measure ambient lighting conditions and
adjust the on/off condition of the display backlighting
accordingly.
Data displayed
•
Apparent and true wind speed
•
Apparent and true wind angle
•
Maximum true wind speed
•
MAX/LOW true wind speed alarm
•
High/Low apparent wind angle alarm
•
Beaufort wind speed
•
VMG to windward
The FI-503 displays critical digital navigation
data such as depth, speed, temp, and
weather data on a 3-way split screen.
Data displayed
1
•
Current depth
•
Shallow/deep alarm
•
Shallow/deep anchor alarm
•
Wind angle
•
High/Low apparent wind angle
2
•
Boat speed
•
MAX/AVG STW
•
SOG
•
MAX/AVG SOG
•
VMG to windward
•
Wind
speed
•
MAX true wind
•
MAX/LOW true wind
speed alarm
•
Beaufort wind speed
3
•
LOG
•
Trip
•
Count up/down timer
•
Water
temperature
•
Air temperature
•
Air pressure
•
Humidity
•
Wind chill temperature
•
Dew point
Apparent and True Wind Angle are displayed
in both analog and digital format when
connected to the FI-5001/5001L or other
CAN bus wind measurement devices.
The FI-502 provides detailed and precise
wind bearing measurements from 60 Port to
60 Starboard, an important range for Close
Hauled (CH) points of sail.
The FI-504 and FI-507 feature large digital displays with
easy-to-read characters presenting all of the information
available in the CAN bus network*. Alternating data display
mode switches the user-selected information in 3-second
intervals.
Data displayed
•
Displays all information on the FI-50 series*
•
NAVIGATION
(Bearing/distance to WPT, XTE, WPT number/name, L/L, Satellites
tracked, Roll & Pitch)
•
ENVIRONMENT (Battery voltage, Time & Date)
•
ENGINE (Trip fuel used, Fuel consumption, Engine RPM)
*
Except ROT. ROT can be displayed on FI-505.
The FI-505 provides a digital compass
readout with an analog “Off Course”
needle that greatly assists the
helmsman in maintaining a desired
course. When connected to satellite
compass, smooth and precise ROT
(Rate Of Turn) of the boat is shown
with the analog needle. The needle
can also be used to verify autopilot
steering performance.
Data displayed
•
Current heading
•
Locked heading
•
Average heading
•
Course over ground
•
ROT
When connected to an autopilot,
the analog FI-506 Rudder Angle
Display shows precise rudder
angle information.
Data displayed
•
Rudder angle
FI-503 FI-504 FI-507 FI-505 FI-506FI-501
Depth/Speed/Temp Sensor
DST-800
Frequency: 235 kHz
Cable: 6 m
Wind Transducer
FI-5001/FI-5001L
Power supply: 12 VDC, less than 40 mA
Transducer cable: 30/50 m
Junction Box
FI-5002
CAN bus backbone x 2 ports
CAN bus x 6 ports
Power supply: 12 VDC, less than 2A
FI-502
DIGITAL MULTI / MULTI XL COURSE PILOT RUDDERWIND CH WIND
Specifications of FI-50 series
Easy to install
Easy to Read with Silver Bright LCD Display
FI-503
DIGITAL
FI-504
MULTI
Operational guide description on the front panel
22
mm
41
mm
22
mm
Daytime Sunset or after
Back Light
Turns On
Back Light
Turns Off
Automatic Backlight Adjustment
Automatic Detection
Display: Analog and digital LCD (FI-501, 502, 505)
Digital LCD (FI-503, 504, 507)
Analog (FI-506)
Power supply: 12 VDC, less than 0.1 A
Temperature: –15°C to +55°C
Waterproofing: IP56
Surface mount installation Flush mount installation
with optional front panel
Surface Mount the displays with a hole saw and install 4 screws
under the front bezel. Installations are easy and clean with a finished
appearance (1"(26mm)bulkhead protrusion)
Optional “Low Profile” Flush Mounting front panels provide
a cosmetic match to NN3D Displays and a custom console
appearance (0.4"(10mm)bulkhead protrusion)
1 DIN type 1.5 DIN type
FI-5001 FI-5001L
Wind Transducer
Wind Transducer
12 V
Basic Configurations
Sail Boat
Power Boat
System Configurations
Wind Transducer
12 V
DigitalWind Multi
12 V
Depth/Speed/Temp
Sensor
Depth/Speed/Temp
Sensor
Depth/Speed/Temp
Sensor
WAAS/GPS
Antenna
Wind Multi Multi XL
Multi XL
Digital
Network Radar Sensor
Navnet 3D
Multi Function
Display
Wind Transducer
Transducer
Depth/Speed/Temp
Sensor
Wind MultiDigital
Network Radar Sensor
Navnet 3D
Multi Function
Display
DigitalWind
CAN bus
Ethernet
others
Wind Transducer
FI-501 FI-503
JUNCTION
BOX
MULTI FUNCTION
DISPLAY
DFF1
HUB
* 12V power supplied from NavNet 3D
* 12V power supplied from NavNet 3D
Satellite Compass Weather Station
Junction Box
WAAS/GPS
Antenna
Junction Box
Weather Station
To Previous Page
Loading...
