Gardner Denver CYCLOBLOWER H.E. Series

Questions and Answers

R
Rhonda GrantAug 14, 2025
How to fix excessive discharge temperature in Gardner Denver Industrial Equipment?
- W
  william23Aug 14, 2025
  Excessive discharge temperature in your Gardner Denver industrial equipment can be caused by several factors. First, check for a restricted inlet flow and clean the air filter, correcting any restrictions. Also, reduce excessive discharge pressure and correct any restrictions. If the equipment is operating below the allowable speed, increase the speed and reduce pressure or vacuum. Finally, worn clearances can also cause this issue, requiring a rebuild by factory-trained personnel.
B
brian76Aug 17, 2025
Why does Gardner Denver CYCLOBLOWER H.E have excessive power consumption?
- D
  Donna ChristensenAug 17, 2025
  Excessive power consumption in your Gardner Denver industrial equipment could be due to several reasons. The speed might be too high, so try reducing it. High pressure or vacuum can also cause this, so remove the cause. Knocking, rotor tip drag, or contact issues can contribute, so address those. Finally, worn clearances can lead to increased power consumption, requiring a rebuild.
M
melissa33Aug 20, 2025
What to do if Gardner Denver CYCLOBLOWER H.E Industrial Equipment has low air flow?
- B
  bgardnerAug 20, 2025
  Low air flow in your Gardner Denver industrial equipment can stem from a few issues. First, check for a restricted inlet flow and clean the air filter, correcting any restrictions. Slipping belts can also cause this, so tighten them. Ensure the speed is correct by checking it with a tachometer or strobe. If the discharge pressure is too high, reduce it and correct any restrictions. Lastly, worn clearances may be the culprit, requiring a rebuild.
D
Desiree FergusonAug 25, 2025
How to reduce excessive vibration in Gardner Denver CYCLOBLOWER H.E?
- S
  Sheena RobbinsAug 25, 2025
  Excessive vibration in your Gardner Denver industrial equipment can be caused by several factors. Check for misalignment and align couplings and belt drives. Knocking, rotor tip drag, or contact issues can contribute, so identify and remove the cause. Ensure rotors are free of scale and process material to address unbalanced rotors. Also, check all mounting bolts and tighten as necessary if blower or driver bolts are loose. Correct piping configuration to resolve piping resonance. Increase rigidity and mass of the foundation to address foundation resonance. Finally, worn bearings or gears may require a rebuild.
D
Dale RiveraAug 27, 2025
What causes excessive oil or bearing temperature in Gardner Denver Industrial Equipment?
- M
  Monica WheelerAug 27, 2025
  Excessive oil temperature or bearing temperature in your Gardner Denver industrial equipment can be attributed to a few things. A dirty heat exchanger can cause this, so clean the heat exchanger on the lubrication system. Excessive bearing load can also be a factor, so reduce belt tension and check shaft coupling alignment. Worn bearings or gears might also be the reason, requiring a rebuild.
S
Stacy JohnsonAug 31, 2025
What to do about knocking, rotor tip drag, or contact in Gardner Denver CYCLOBLOWER H.E?
- J
  Jennifer MorganAug 31, 2025
  Knocking, rotor tip drag, or contact in your Gardner Denver industrial equipment can be addressed by checking a few things. Ensure proper shimming of feet to the foundation and correct any piping-induced strains to address housing distortion. Reduce operating pressure or vacuum and check the relief valve if there's excessive pressure or vacuum. If there's excessive discharge temperature, remove the cause. Bearing failure or incorrect timing might also be the cause, requiring a rebuild.
M
Matthew JenningsSep 2, 2025
How to stop an oil leak in Gardner Denver CYCLOBLOWER H.E Industrial Equipment?
- A
  Ashley MitchellSep 3, 2025
  An oil leak in your Gardner Denver industrial equipment can be due to a few reasons. If there's low reservoir vacuum, adjust the reservoir vacuum with the louver. If there's too much oil in the reservoir, reduce the oil level to the recommended level. If there is a faulty oil seal, it may require a rebuild.
R
ronald96Sep 6, 2025
Why does the motor shut off soon after starting due to a lubrication system fault in Gardner Denver CYCLOBLOWER H.E?
- S
  Scott MaynardSep 6, 2025
  A lubrication system fault causing the motor to shut off soon after starting in your Gardner Denver industrial equipment can be due to several reasons: * If the reservoir vacuum is too low, increase the vacuum with the adjustable louver and tighten the oil fill cap. * If the oil injection pressure is too low, address restrictive plumbing, increase injection pressure, prime pump lines, and change the oil filter. * If the oil temperature is too high, clean the heat exchanger and check the blower. * If the oil temperature is too low, wait for the oil heater to heat the reservoir and insulate reservoir walls from airflow. * Remove the cause of fan motor fault. * Check the signal or bypass with a jumper if not used to fix remote run/reset signal failure.
T
Terry ColemanSep 9, 2025
Why is there no air flow in Gardner Denver CYCLOBLOWER H.E Industrial Equipment?
- T
  Tammy LopezSep 9, 2025
  If there is no air flow in your Gardner Denver industrial equipment, check if the rotation direction is wrong and correct it.