FCC AND IC DECLARATIONS
Compliance statement (part 15.19)
This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CRN d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est authorisée aux
deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
INDUSTRY CANADA INFORMATION (additional)
This device complies with RSS-210 of the Industry Canada Rules.
This class B digital apparatus complies with Canadian ICES-003
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator
and your body.
The final end-product must be labeled in a visible area with the following: “Contains IC: 6271A-RT2”.
AVIS D’INDUSTRIE CANADA (supplémentaire):
Cet appareil est conforme à la norme CNR-210 des règlements d’Industrie Canada.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
Avis d’Industrie Canada sur l’exposition aux Rayonnements: Cet équipement doit être installé et utilisé à
une distance minimale de 20 cm entre le radiateur et votre corps.
Le produit final final doit être étiqueté dans un endroit visible par le texte suivant: "Contains IC: 6271A-RT2".
Warning (part 15.21)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This in particular is applicable for the antenna which has been delivered with the
RF Exposure (OET Bulletin 65)
To comply with FCC RF exposure requirements for mobile transmitting devices, this transmitter should only be used or installed at locations where
there is at least 20cm separation distance between the antenna and all persons.
Information to the User (Part 15.105 (b))
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Module integration instructions:
This device is intended only for integration under the following conditions: (I).The antenna must be
installed such that 20 cm is maintained between the antenna and users. (II). The transmitter module may
not be co-located or operating in conjunction with any other transmitter or antenna. (III). The module shall
be only used with the external antenna(s) that has been originally tested and certified with this module,
custom design antennas may not be used without re-certification.
As long the conditions above are met, further transmitter testing will not be required. However, the
integrator is still responsible for testing the end-product (¨host¨) towards any additional compliance
requirements required with this module installed (for example, digital device emissions, PC peripheral
requirements, etc.).
Validity of using the module certification:
In the event that these conditions cannot be met, then the FCC authorization for this module in
combination with the host equipment is no longer considered valid and the FCC ID of the module cannot
be used on the final product. In these circumstances, the integrator will be responsible for re-evaluating
the end-product (including this modular transmitter) and obtaining a separate FCC authorization.
End product labeling:
The final end-product must be labeled in a visible area with the following: “Contains FCC ID: TVO-RT2”.
Information that must be placed in the end user manual:
The integrator has to be aware not to provide information to the end user how to install or remove this RF
module in the user's manual of the end-product which integrates this module. The end user manual of the
final end-product shall include all required regulatory information/warning as shown in this manual.
To Next Page
Loading...