GE Profile Advantium PSB2201NSS - User Manual

Specification Created 9/08
240441
Listed by
Underwriters
Laboratories
PSB2201NSS
GE Profile Advantium
®
240 Wall Oven
For answers to your Monogram,
®
GE Profile
™
or
GE
®
appliance questions, visit our website at
ge.com or call GE Answer Center
®
service,
800.626.2000.
cooking_tower_solid_floor.eps
C
L
(Must support 130 lbs.)
2 x 4’s or
equivalent
solid floor
Suitable
bracing
to support
runners
21-5/8"
over centerline
of cabinet
A=Allow 1" overlap of oven over top and bottom edges of cutout.
B=Allow 11/16"-3/4" for overlap ov oven over side edges of cutout.
Cabinet
Width
(inches)
W
Width
H
Height
D
Depth
(excluding
handle)
X
Cutout
Width
Y
Cutout
Height
Z
Cutout
Depth
(minimum)
PSB2200/1 without
accessory drawer
30 29-25/32 19-1/8 21-3/4 25-1/8 17-1 /2 23-1 /2
PSB2200/1 with
accessory drawer
30 29-25/32 22-1 /4 21-3/4
25-1/8 to
28-1/2*
21 23-1/2
*For existing cutouts a maximum width of 28-1/2" is acceptable
A=Allow 1" overlap of oven over top and bottom edges of cutout.
B=Allow 11/16"-3/4" for overlap ov oven over side edges of cutout.
Note: Cabinets
installed adjacent
to wall ovens must
have an adhesion
spec of at least a
194°F temperature
rating.
Note: 2" minimum
between cutouts
when installed
above warming
drawer or single
wall oven.
Installation
Information:
Before installing,
consult installation
instructions packed
with product for current
dimensional data.
Cutout width
25-1/8"
30
Required
cutout location
36-3/4"
minimum
from floor
Junction
box
location
(240-Volt
models only)
A=Allow 1" overlap of oven over top and bottom
edges of cutout.
B=Allow 11/16"-3/4" for overlap ov oven over side
edges of cutout.
4-3/16
17-1/2"
Cutout height
A
B
23-1/2"
Cutout depth
29-25/32"
19-1/32"
21-1/2"
Excluding
Handle
Advantium Wall Oven Dimensions (in inches)and
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
Construct Solid
Bottom Min.
3/8" Plywood
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides.
(Must Support
150 lbs.)
Conduit
(48-1/2"
long)
adv_240_120_cooktower_dia.eps
1" Min. above toekick or adjust
to oven installation height
2" MIN between cutouts
2-1/2" MIN between cutouts
recommended—2" MIN required
9-1/4" cutout height
28-1/2" cutout width
Junction box location
A
B
A
B
Construct Solid Bottom
MIN 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides.
(Must Support 150 lbs. for Advantium)
(Must Support 200 lbs. for Wall Oven)
4-3/16
D
Excluding
Handle
H
W
Conduit
(46" long)
Cabinet width
(240-volt models only)

GE Profile Advantium PSB2201NSS Specifications

General

Brand	GE
Model	Profile Advantium PSB2201NSS
Category	Oven
Language	English