Gendex GX CB-500 - Appendix C - Assembly Report Form Sample

218 pages

To Next Page

To Previous Page

Assembly Report Sample

C-1

G990710 30 June 2008

Assembly Report Form Sample

Complete Address of Installation

G1-15-1-0

Main Page

Default Chapter3
- Table of Contents3
Chapter 1 - Introduction9
- System Description9
- Major System Items10
- About the Operators' Manual11
  - Conventions Used in the User Manual11
- Standard Limited Warranty12
Chapter 2 - Safety Items15
- Important Safety Information15
- System Safety Devices20
- Sample Site Plan21
  - Interlock and Warning System Schematic22
- Cabling Requirements23
- Emergency Removal of a Patient23
- System Labels24
- Error Messages27
Chapter 3 - System Controls and Indicators29
- Operator Control Box29
- Patient Emergency Stop Control30
- Patient Alignment Panel30
- System Status Indicators30
Chapter 4 - System Startup and Shutdown31
- System Startup31
- System Shutdown31
Chapter 5 - System Assembly33
- Initial Preparation33
- Required Tools33
- Abbreviations33
- Inventory of Unit Items34
- System Assembly36
Chapter 6 - Leveling and Alignment49
- Level Gantry49
- Patient Chair Alignment52
- Laser Alignments56
  - Adjust Centerline Laser56
  - Adjust Crosshair Laser59
- Head Holder Alignment62
Chapter 7 - Calibration63
- Panel Calibration63
- Collimators Calibration65
- Geometry Calibration66
Chapter 8 - Quality Assurance71
- QA Phantom Test71
- QA Water Phantom Test80
- PAN Phantom Test90
- Radiation Output Test93
  - Measured Dose93
  - Interpretation94
Chapter 9 - Troubleshooting and Adjustments95
- Detector Pivot Adjustment (Receptor Panel)95
- IEC IC Command Codes97
  - Home Commands97
  - Movement Commands97
- Read Commands98
- X-Ray Commands100
- Miscellaneous Commands101
Chapter 10 - Wall Mount Control Box103
- Wall Mount with Cable Exposed103
- Wall Mount with Cable Inside Wall106
Chapter 11 - Networking Support Setup111
- Networking Support Overview111
- Networking Data Flow111
- Network Support Installation/Setup112
- Sweeper Service116
  - Sweeper Controller116
- Network Failures117
  - No Network Access at Startup117
  - Network Fails During Operations118
- Limitations of Networking Support119
Chapter 12 - Remote System Import and Export121
- Remote System Import and Export Overview121
- Remote System Import121
- Import Installation and Setup122
  - Set up DICOM Worklist Interface122
  - Set up Practice Management Interface124
- Import Patient Data125
- Remote System Export126
- Export Installation and Setup126
- RSSM Log128
- Send Patient Data to a Remote System129
Chapter 13 - Product Information131
- Technical Specifications131
- Power Requirements132
  - Apparent Resistance of Supply Mains132
- Weight133
- Power Cords Required Outside of the United States133
- Environmental Specifications134
  - Operating134
  - Transportation and Storage134
- Acquisition Computer134
- Patient Support Chair135
- Disposal135
- Extension Cords135
- External Item135
- Cleaning135
- Electromagnetic or Other Interference (Emissions and Immunity)136
- Equipment Standards138
- Equipment Class138
- Preventive Maintenance Schedule - for Owner / User139
- Planned Maintenance - 12 Month Schedule139
  - Cleaning140
  - Planned Maintenance Checklist140
- Replaceable Parts - Reference List142
- Accessories143
Chapter 14 - Illustrated Parts Breakdown147
- System Assembly148
  - System Assembly Parts List149
- Overhead Assembly150
  - Overhead Assembly Parts List151
- Rotation Drive Assembly152
  - Rotation Drive Assembly Parts List153
- X-Ray Source Assembly154
  - X-Ray Source Assembly Parts List155
- Receptor Panel Assembly156
  - Receptor Panel Assembly Parts List157
- Chair Assembly158
  - Chair Assembly Parts List159
- Upper Chair Assembly160
  - Upper Chair Assembly Parts List161
Chapter 15 - Radiation Environment Survey163
- Conditions of Operation - 8.9 and 23.0 Second Scans164
- Scatter Measurements for 8.9 Second Scans165
  - Standard (Full-Beam) Diameter 8.5 - Height 8.5 CM165
  - Half Beam Diameter 14 - Height 8.5 CM167
- Scatter Measurements for 23 Second Scans169
  - Standard (Full-Beam) Diameter 8.5 - Height 8.5 CM169
  - Half Beam Diameter 14 - Height 8.5 CM Scan170
- Scatter Measurements for PAN Scan171
- Scan Times and Settings173
- Dose and Imaging Performance Information174
- Dose Profile175
- Sensitivity Profile177
- Drywall Attenuation178
- Recommended Operating Requirements179
- X-Ray Tube Assembly180
Appendix A - Icatvision, Icattransfer, & RSQM Installation185
- Icatvision185
- Icattransfer189
- Rsqm192
- RSQM Installation and Setup192
- Query and Retrieve Images194
- Status Messages197
Appendix B - I-Catvision Release Notes199
Appendix C - Assembly Report Form Sample209
Appendix D - System Schematics211

Gendex GX CB-500 - Appendix C - Assembly Report Form Sample

Table of Contents

Related product manuals