ghd Glide - Page 4

EN
65
5. Do not use an extension power cord with this appliance.
6. Do not use a voltage inverter or generator with this appliance.
7. Your ghd product is a class II electrical appliance and should
not be connected to an earth connection.
warning: hot surfaces
The ghd hot brush heater plate is hot for eective styling.
To reduce the risk of burns:
1. NEVER touch the heated plate of the hot brush.
2. When not styling always lay the ghd hot brush on a at heat-resistant
surface such as a ghd hot brush heat mat.
3. When styling is complete, always switch o the ghd hot brush and unplug
it from the power supply.
4. Wait for the ghd hot brush to cool before storing.
5. When the ghd hot brush has cooled, fold the power cord in the same way as
it was rst delivered in its packaging. Do not wind it around your hand or the
body of the ghd hot brush as this can lead to early failure of the power cord.
Your ghd glide™ is not only
attractive to you, but also to
your children. Please ensure
you always store your ghd
hot brush out of reach of
children, particularly during
use, especially when cooling.
operation
Ensure that hair is completely dry before using the ghd glide™.
1
2
3
4
1 Heater plate
2 On/O Switch and indicator light
3 Power cord
4 Ioniser
1. Plug your ghd hot brush into the power supply. The switch surround will ash
white for less than 1 second and beep to indicate that it is now connected to
mains electricity. The appliance is now in standby mode.
2. To turn on the ghd hot brush, press and hold the ON/OFF button for at least
1 second. The ghd hot brush will play a short start-up tune and a light will
pulse to indicate that the hot brush is heating up.
IMPORTANT: the ghd hot brush heats up quickly, so don’t touch the hot
heater bristles! Once the ghd hot brush has reached operating temperature,
it will bleep and the light will remain illuminated to indicate that it is ready
to use.
3. When you have nished your styling session, press and hold the ON/OFF button
for more than 2 seconds to turn the appliance o. A shut down tune will play to
indicate the appliance has been turned o. Once turned o, it is best practice
to unplug the appliance from the mains electricity and allow it to cool in a safe
place. For safe cooling place the appliance on a ghd heat resistant mat and
allow to cool.
WARNING: while the appliance is cooling down do not touch the
heated bristles or allow children or those with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge
to touch the appliance whilst it is cooling.
the ghd glide™ has the following safety features:
1. Sleep mode: if the ghd hot brush has been left on and has not been used
for 60 minutes, a safety feature will automatically turn the hot brush o. The
hot brush will play the sleep mode tune, the plate will start to cool and the
light will slowly pulse till the plate reaches a safe temperature.
a. To restart the appliance while it is in sleep mode, simply turn it on by
pressing and holding down the ON/OFF button for more than 1 second.
b. Note that although ghd hot brush is turned o, it is still connected to the
mains and should be unplugged from mains electricity at the earliest
opportunity.
2. Fail safe: in the unlikely event of a control system error, for safety the heaters
will turn o, the ghd hot brush will emit bleeps and the light will ash red
every ve seconds. If this occurs un-plug and re-plug at the power supply
and re-start. If the unit does not re-start or the problem persists, contact ghd
Customer Service for advice.
user maintenance instructions
Cleaning your ghd glide™
1. Unplug the ghd hot brush from the mains power supply.
2. Always allow the ghd hot brush to cool before attempting to clean it.
3. Never immerse the appliance in water.
4. Remove all hair from in between the bristles after every usage. Wipe clean
any build-up of styling products with a damp cloth or soft brush (do not
scrub) from both bristles and heater plate.
5. Do not use an abrasive cleaning uid to clean, as damage will occur.
Storage
1. Always allow the ghd hot brush to cool down before storing away.
2. When the ghd appliance has cooled down, fold the power cord in the same
way as it was rst delivered in its packaging. Do not wrap the supply cord
around the ghd appliance as this can strain the cord and cause premature
supply cord failure.
failure to operate
If your product stops working and the red fault light ashes, please follow
the procedure below:
1. Switch o the unit
2. Unplug the unit from the plug socket
3. Wait for 5 seconds and then plug the unit back into the wall
4. Switch the unit back on
If this occurs repeatedly, please contact your local ghd service centre.
For UK plugs, please ensure that the tted fuse is intact and functioning;
if it is not, replace it with an identically rated British Standard Fuse.
If in doubt or for further advice, please visit the help section of ghdhair.com
or contact an approved ghd stockist or contact ghd Customer Service for
further advice.
manufacturer’s guarantee
All ghd electrical products are individually tested before leaving the factory.
However in the unlikely event of the product proving defective due to faulty
workmanship or materials, then, at its sole discretion, ghd will replace the
product at no charge with an identical or equivalent product within two years
from the original date of purchase. A replacement product assumes the
remaining guarantee of the original product or 180 days, whichever provides
longer coverage for you. When a product is exchanged, any replacement item
becomes your property and the replaced item becomes property of ghd.
To claim under this guarantee please visit ‘ghdhair.com/returns’ and follow the
onscreen instructions to complete your return. Please ensure that you include a proof
of purchase with any returned product. Therefore please ensure you keep your proof
of purchase in a safe place.
This guarantee only applies to genuine ghd products
purchased through ghd-approved stockists, and does
not cover products repaired or serviced by anyone other
than ghd personnel or ghd representatives. Note that this
guarantee may be invalidated where serial numbers or
identication have been erased, damaged or modied.
This does not aect your statutory rights.
*Neither Jemella Group Limited nor its subsidiaries provides
replacement parts for any of its electrical units. If you do not have access to the internet
please return your ghd electrical product to the closest ghd address as printed in this leaet
or on the packaging, together with your proof of purchase. For customers in Australia and
New Zealand, please phone your closest ghd oce on the number printed in this leaet.
Australia only
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
Not to be reproduced