ghd rise - Page 4

65
EN
1. Plug the ghd rise into the power supply. The ghd rise will momentarily ash
around the ON/OFF switch to indicate that it is connected to a power supply
and is in standby mode.
2. To turn on the ghd rise, press and hold the ON/OFF button for at least
1 second. The ghd rise will play a short start-up tune and a light will
pulse to indicate that the device is heating up.
3. IMPORTANT: the ghd rise reaches the required temperature in seconds, so
be careful not to touch the hot appliance barrel or bristles! Once the ghd rise
has reached temperature, it will bleep and the light will remain illuminated to
indicate that it is ready to use.
4. When you have nished your styling session, press and hold the ON/OFF
button for more than 2 seconds to turn the appliance o. A shut down tune will
play to indicate the appliance has been turned o. Once turned o, it is best
practice to unplug the appliance from the mains electricity and allow it to cool
in a safe place. For safe cooling place the appliance on a ghd heat resistant
mat using the built-in safety stand and allow to cool.
WARNING:whiletheapplianceiscoolingdowndonottouchthebarrel
orbristles,orallowchildrenorthosewithreducedphysical,sensory
ormentalcapabilities,orlackofexperienceandknowledgetotouch
theappliancewhilstitiscooling.
Your ghd rise is not
onlyattractivetoyou
butalsotoyourchildren.
Pleaseensureyoualways
storeyourghdstyler
outofreachofchildren,
particularlyduringuse,
especiallywhencooling.
ghdrisehasthefollowingsafetyfeatures:
1. Sleepmode:If the ghd rise has been left on and has not been used for
30 minutes, a safety feature will automatically turn the hot brush o. The hot
brush will play the sleep mode tune, the barrel will start to cool and the light
will slowly pulse till the barrel reaches a safe temperature.
a. To restart the appliance while it is in sleep mode, simply turn it on by
pressing and holding down the ON/OFF button for more than 1 second.
b. Note that although ghd rise is turned o, it is still connected to the mains
and should be unplugged from mains electricity at the earliest opportunity.
2. Protect Mode: The ghd rise can protect itself against adverse events or
power uctuations, for safety the heaters will turn o, the ghd hot brush will
emit a bleep and the light will ash white every ve seconds. If this occurs
un-plug and re-plug at the power supply and then re-start.
3. Failsafe: In the unlikely event of a control system error, for safety the
heaters will turn o, the ghd rise will emit bleeps and the light will ash red
every ve seconds. If this occurs un-plug and re-plug at the power supply
and re-start. If the unit does not re-start or the problem persists, contact
ghd Customer Service for advice.
user maintenance instructions
Cleaningyourghdrise
1. Unplug ghd rise from the mains power supply.
2. Always allow ghd rise to cool before attempting to clean it.
3. Never immerse the appliance in water.
4. Wipe the handle and barrel of the appliance with a damp cloth.
Do not use sharp or abrasive detergents or corrosive products.
5. Remove all hair from in between the bristles after every usage.
Wipe clean any build-up of styling products with a damp cloth
or soft brush (do not scrub) from both bristles and heater plate.
Storage
1. Always allow your ghd rise to cool down before storing away.
2. When the appliance has cooled down, fold the power cord in the same way as
it was rst delivered in its packaging. Do not wrap the supply cord around the
appliance as this can strain the cord and cause premature supply cord failure.
cordorplug.Ifthepower
cordorplugisdamaged,
itmustbereplacedby
JemellaLtd.
1. Only use with 110–240V, 50-60 Hz power supply.
2. The appliance should never be left unattended when plugged in.
3. Keep the power cord away from heated surfaces. Do not wrap the power
cord around the appliance. Do not hang the ghd rise by the power cord.
4. Always unplug the ghd rise immediately after using.
5. Do not use an extension power cord with this appliance.
6. Do not use a voltage inverter or generator with this appliance.
7. Your ghd product is a class II electrical appliance and should
not be connected to an earth connection.
warning: hot surfaces
The ghd rise barrel is hot for eective styling.
To reduce the risk of burns:
1. IMPORTANT: the ghd hot brush heats up quickly, so don’t touch the bristles
as they can get hot!
2. When not styling always lay the ghd rise on a at heat-resistant surface such
as a ghd heat mat.
3. When styling is complete, always switch o the ghd Rise and unplug it from
the power supply.
4. WARNING: while the appliance is cooling down do not touch the bristles
or barrel.
5. Wait for the appliance to cool before storing.
6. When your ghd Rise has cooled, fold the power cord in the same way as it
was rst delivered in its packaging. Do not wind it around your hand or the
barrel or handle of the ghd rise as this can lead to early failure of the power
cord.
operation
Ensurethathairiscompletelydrybeforeusingtheghdriseappliance.
IMPORTANT:careshouldbe
taken to prevent getting hair
tangledintheghdhotbrush
bristles,donotwraplarge
amounts of hair around
thebarrel.
Iftanglingoccurs,switch
othehotbrushbefore
detanglinghair.
1 Cool tip
2 Barrel
3 Bristles
4 Stand
5 ON/OFF Switch
6 Handle
7 Power cord
Not to be reproduced