Gigabyte B650M AORUS PRO AX - Page 23

- 23 -
F_USB30
F_U
B_ 
F_  F_ 

_
B
BS_
B
SB_
B
_S

S_
_
B
_U
_
B


 
S  
 
123
 
123
 
123
 
123
1
1
1
1
BSS
S
_S 
SSU
 
1 2 3  
 S3
BSSS

U
 __ 3
F_USB3F
S  _
S  _
S  _
SF


B_
B_
F
_0
S
S
_0F
_F
_
_
__B


U
S  _S
_
SF_
B 
USB0_B
B_
B_
F_USB3

F_USB303

_

_3U
S_
_S
SS_F 
_
_
F 
_SB
12) M2A_CPU/M2B_CPU (M.2 Socket 3 Connectors)
There are two types of M.2 SSDs: M.2 SATA SSDs and M.2 PCIe SSDs. This motherboard only supports
M.2 PCIe SSDs. Please note that an M.2 PCIe SSD cannot be used to create a RAID set with a SATA
hard drive. Please navigate to the "Conguring a RAID Set" page of GIGABYTE's website for instructions
on conguring a RAID array.
* Types of M.2 SSDs supported by each M.2 connector:
M.2 PCIe x4 SSD M.2 PCIe x2 SSD M.2 SATA SSD
M2A_CPU
a a
r
M2B_CPU
a a
r
F_USB30
F_U
B_ 
F_  F_ 

_
B
BS_
B
SB_
B
_S

S_
_
B
_U
_
B


 
S  
 
123
 
123
 
123
 
123
1
1
1
1
BSS
S
_S 
SSU
 
1 2 3  
 S3
BSSS

U
 __ 3
F_USB3F
S  _
S  _
S  _
SF


B_
B_
F
_0
S
S
_0F
_F
_
_
__B


U
S  _S
_
SF_
B 
USB0_B
B_
B_
F_USB3

F_USB303

_

_3U
S_
_S
SS_F 
_
_
F 
_SB
80
60 42
M2A_CPU
80
60 42
M2B_CPU
& Please visit GIGABYTE's website for details on using M.2 EZ-Latch.
Install the M.2 SSD: https://www.gigabyte.com/WebPage/919/M2-ezlatch.html
* Motherboard heatsink design may vary by model.
110
110
Follow the steps below to correctly install an M.2 SSD in the M.2 connector.
Step 1:
To access the M.2 slot you want to use, unfasten the screws on the motherboard heatsink diagonally to
remove the heatsink. Locate the proper mounting hole for the M.2 SSD to be installed and then install the
M.2 EZ-Latch clip rst.
• If you want to install an M.2 SSD that came with its own heatsink, you have to remove the
EZ-Latch clip rst and use the provided screw and standoff to fasten the SSD.
• If you want install an M.2 SSD in the 110mm hole that already has a motherboard heatsink
standoff, be sure to remove the EZ-Latch clip rst and use the motherboard heatsink screw to
secure the heatsink and SSD.
Step 2:
Insert the M.2 SSD into the M.2 connector at an angle. Press down on the front end of the M.2 SSD and
close M.2 EZ-Latch clip to secure the M.2 SSD.
Step 3:
Remove the protective lm from the bottom of the motherboard heatsink and then replace the heatsink
and tighten the screws diagonally.