GIRBAU EH040 - Page 76

To Next Page

To Previous Page

Troubleshooting 76

Code 429159

Rev. 15/0717

Note 1. When the message “Disconnect the washing machine supply” appears, it is recommended to:

 Disconnect the ON switch.

 Wait the safety time for disconnecting the door (approximately 3 minutes). Open the door.

 Connect the ON switch again.

 Start a new wash cycle.

Main Page

Default Chapter3
- Table of Contents3
Safety Instructions6
1 Description10
- Characteristics10
- Protection, Safety and Control Elements11
- Safety Functions11
2 Control Panel12
- Connection and Stop Devices12
- Screen12
- Keyboards13
- Card Reader13
3 Main Menu. Intervention Modes14
4 Executing Programs15
- Starting the Washing Machine. Main Menu15
- Loading the Washing Machine. Selecting and Starting a Wash Program15
- Information about Functions. Description of the Screens16
- INFO Screen17
- Manual Modification18
- Crease-Guard Stop. RINSE HOLD Function19
- Stop and Door Opening Modes19
- Delayed Start of a Wash Program20
- Unbalance Control20
- Systems to Aid Loading and Unloading21
  - Control Panel Operation22
  - Remote Control Operation22
- EASY LOAD System Operation24
- TILT System Operation25
- TILT + EASY LOAD System Operation27
- Pausing a Program as a Result of a Dosing Unit Warning29
5 Pre-Set Programs30
- Interpreting the Icons in Tables of Pre-Set Programs31
- Contents of Pre-Set Programs32
6 Programming Mode34
- Defining Programming Concepts34
- Programming Mode Menus34
7 Programming a New Wash Program35
- Access to Programming a New Program36
- Identifying the New Program36
- Programming a Program Phase37
- Manual Program. Definition and Use45
- INFO A6 Mode46
8 Modifying Programs50
- Modifying a Program50
- Copying a Program into an Empty Program52
- Locking and Unlocking the Use of a Program53
- Erasing a Program53
- Modifying the Name and Viewing the Content of Pre-Set Programs53
9 Using the Card54
- Copy from Machine to Card55
- Copy from Card to Machine55
- Consulting the Card and Changing the Program Name56
- Erasing a Program on the Card56
10 System Tools57
- Configuration Menu. Introduction and Access57
- Configuring Operation and Programming Parameters58
- Setting the Clock65
- Initializing the Card66
- Managing Access Codes66
11 Information Menu67
- General Information. Content67
- Operation Counters67
- Alarm Counters68
- Executed Program Counters69
- Load Counters69
12 Text Messages69
- Programming Messages and Moment of Display69
13 Cleaning of Recovery Tank Menu70
- Configuration of Parameters and Wash Start70
14 Troubleshooting71
- Freeing a Person Trapped Inside the Washing Machine71
- Freeing a Person Trapped by the TILT System71
- Manually Releasing of the Security Lock72
- Disassembling the Door of the Washing Machine72
- What to Do When73
- System Alarms74
15 Maintenance77
- Washing Machine Cleaning77
- Door Seal Cleaning77
- Cleaning the Solenoid Valve Filters78
- Verifying the Safety Mechanisms78
- Cleaning the Dispenser79
- Greasing the Bearing Housing80
- Checking the Condition of the Bearing Housing Seals81
- General Revision81
- Recovery Tank Cleaning81
16 Service Removal82
- Dismantling82
- Code82
Appendices to the Manual83
Examples of the Use of INFO A6 Mode83
- INFO A6 Mode with the Machine Connected to a Smart External Control Unit83
- INFO A6 Mode as a Trigger of External Signals84
  - Example of Using Multiple External Dosings of the same Duration84
  - Example of Using Multiple External Dosings of Different Durations85
Use of Bath and Proportional Dosing in a Machine Connected to a Dosing Control Unit86

GIRBAU EH040 - Page 76

Table of Contents

Other manuals for GIRBAU EH040

Related product manuals