As a professional power supply product, GODOX PB960
power pack is designed to charge speedlites with external
power input ports, including on-camera flashes from Canon,
Nikon, Sony, and Godox, etc.
With Godox PB960 power pack, it takes only one second to
charge flashes such as Canon 580 EX II, Nikon SB-900, and
Sony F58AM at max. power. It can provide up to 1800 full-
power flashes with a Canon 580EX II or Nikon SB-900.
Flashes mentioned above can be used on PB960 by replacing
a plug-in connector cable. In addition, it can charge iPhone,
iPad, iPod and other products with a USB interface.
With the MCU (Micro-Controller Unit), this product integrates
software protection and hardware protection and adopts heat-
resistant nylon plastics, ensuring higher safety and reliability.
There are high-voltage components inside the product. Do
not carry out disassembly or maintenance by yourself, or
electric shock may occur.
Keep out of the reach of children.
Please do not touch the metal part of the plug and the socket.
Please do not use this product under flammable conditions
(such as areas containing flammable gases or liquid
chemicals), or it may result in fire disaster.
Make sure all plugs and sockets are reliably and firmly
connected.
This product is not water resistant. Please keep it away from
rain, snow or humidity.
Please do not leave or use this product at a temperature of
above 40℃ (104°F).
Since this product has a much higher power output than the
ordinary built-in battery of the flash, the flash may be
damaged when used at high frequency and high power. To
avoid overheating of the flash, please allow a break of about
10 minutes after 40 continuous full-power flashes.
Only when this product is at power-off status, can the plug be
inserted or removed.
With GODOX PB960 power pack, it takes only one second
to charge Canon 580EX II, Nikon SB900, Sony F58AM
flashes at maximum power, and 1800 times of flashes in full
brightness is supported.
If the battery of the power pack requires replacement, please
contact a professional service outlet to replace it with a new
tailor-made battery supplied by GODOX.
Damage due to unauthorized disassembling of the power
pack is not covered by the warranty.
Damage due to operations violating the instructions in this
Instruction Manual is not covered by the warranty.
Select a connector cable that is compatible with your product.
Please timely charge the battery according to the indication
of the LEDs.
2.Status Indicators: STATUS1, STATUS2
Thank you for choosing GODOX PB960 power pack
Power Source for FLASH
Warning
Caution
I.Names of Parts
II.Loading/Unloading
Battery Chamber
Loading:
1. Clasp the control unit with the battery chamber;
2. Slide the battery chamber to the left until it locks into place
with a “click”.
AC Charger
Battery pack
Battery charging time
Flash recycling time
Number of Flashes
Dimension
Weight
Lithium battery-11.1V/4500mAH
Approx. 3 hours
Approx. 1s (at full power)
Approx. 1800 times
（for one Canon 580EX II at full power）
159*133.5*49.2MM
540G
VIII.Technical Data
VII.Working Performance
Shoulder Strap
Made In China
This product features
Large-capacity lithium battery (11.1V/4500mAH), which can
provide up to 1800 full-power flashes with a Canon 580EX II or
Nikon SB-900.
Dual outputs for powering two separate flashes without reducing
recycle time
Removable and replaceable battery module. Double your flash
capacity by purchasing a second module.
Concise LED display panel, easy and fast to control
Optimized MCU circuit design, more efficient energy conversion
and more flashes.
Power Connector Cable
(to be sold separately)
Belt Clip
Strap
Lock
Control
Unit
(Upper)
Battery
Chamber
(Lower)
Battery Level Indicator
(LED1, LED2, LED3, LED4)
Status Indicator 2
(STATUS2), for Socket 2
On/Off
Touch
Button
Socket 2
Status Indicator 1
(STATUS1), for Socket 1
Battery
Chamber
Lock
Charging
Port
Socket 1
Accessories
1 2
1 2
Unloading:
1. Slide the battery chamber lock downwards;
2. Slide the battery chamber to the right.
III.Battery Charging
Insert one end of the AC charger into an AC socket (100-
240V) and the other end into the charging port of the power
pack. If the charger indicator turns red, the battery is being
charged. If the charger indicator turns green, the battery is
fully charged. It takes about 3 hours to fully charge the battery.
IV.Operations
Connect the power plug
of the connector cable to
socket 1 or 2 of the power
pack.
Insert the terminal of the
connector cable into the
flash.
Press the On/Off touch
button, and the LED battery
level indicators light up,
indicating the power pack
starts working.
Note: If this product is used for a flash, the flash must
be installed with batteries that have sufficient power.
Turn the power pack by pressing the On/Off touch button.
Turn off the power pack by directly unplugging the connector
cable from the power pack.
off
(i)Start-up
(ii)Power-off
V.Power Pack Status
VI.LED Indicators
1.Battery Level Indicators: LED1, LED2, LED3, LED4
LED4
LED3
LED2
LED1
Status Indicator2
(STATUS2)
Status Indicator 1
(STATUS1)
Battery level
LED
Weak
Low
Middle
To be full
Full
Flicker
ON
ON
ON
ON
LED4LED1 LED2
OFF
OFF
ON
ON
ON
LED3
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
When LED1 is blinking, this product will disable power
output; the battery needs immediate charging before it can
be used again.
Note: Please charge the device for use if it cannot
be powered on.
STATUS1/STATUS2 is off during flash charging and will light
up when the flash is fully charged.
STATUS1/STATUS2 blinks (blinking cycle: 1Hz), indicating
that the flash has been overused. In case of excessively
high temperature inside the power pack, the overheat
protection will be enabled with the power output suspended.
Please wait for at least 10 minutes before using it again.
IX. Maintenance
Power-off status: There is no LED indication, and no power
output from socket 1 or 2. Energy consumption of the entire
unit is so low that the loss of battery power can be ignored.
Testing status: When the connector cable is not inserted into
socket 1 or 2, press the On/Off test button, and only the
battery level indicators light up, indicating the power pack
enters into the testing mode. Press the On/Off touch button
again or wait for 3 seconds to return to the power-off status.
Working status: Insert the connector cable into socket 1 or 2
and press the On/Off touch button, and the LED indicators
light up, indicating the power pack enters into the working
status. Press the On/Off touch button again or unplug the
connector cable from socket 1 or 2 to enter the power-off
status.
* Automatic Power-off Function: The power pack will be
automatically powered off after working for twelve hours, in
case shutdown is missed, leading to long-time power
consumption.
To Next Page
Need help?
General
