●
●
●
●
●
●
Press this button can select left & right swing angle.
Fan blow angle can be selected circularly as below:
Press this button can select up & down swing
angle. Fan blow angle can be selected circularly
as
below:
●
NOTE
NOTE
The function is only available for some models.
●
When selecting " ", air conditioner is blowing
fan automatically. Horizontal louver will automat-
/
Hold " "button above 2s to set your required
swing angle. When reaching your required
angle, release the button.
Press this button continuously more than 2s, the
main un it will swing back and forth from left to right,
and then loosen the button, the unit will stop swinging
and present position of guide louver will be kept
immediately.
Under left a nd right swing mode, when the status is
switched from off to , if press this button again 2s
later, status will switch to off status di rectly; if
press this button again wit
hin 2s, the change of swing
status will also depend on the circulation sequence
stated above.
no display
position)
(stops at current
“
、
、
" may not be available. When air condi-
tioner receives this signal, the air conditioner will blow
fan automatically.
Press this button continuously for more than 2s, the
main unit will swing back and forth from up to down,
and then loosen the button, the unit present position
of guide louver will be kept immediately.
Under u p and down swing mode, wh en the status is
switched fro m off to , if press this button again 2s
later, status will switch to off status directly; if
press this button again within 2s, the change of swing
stat
us will also depend on the cir culation sequence
stated above.
●
●
no display
(horizontal louvers stops
at current position)
When selecting " ", air conditioner is
、 、
ically swing up & down at maximum angle.
When selecting
、
" "
、 、 、
, air condition-
er is blowing fa n at fixed position. Horizontal
louver will stop at the fixed position.
Press " " or " " button once increase or d
ecr-
ease set temperature 1
℃ (°F). Holding " " or
" " button, 2s later, set temperature on remot e
controller will change quickly. On releasing button
after setting is finished, temperatu re indicator on
indoor unit will change accordingly.
When setting T-ON, T-OFF or CLOCK, press " "
or " " button to adjust time. (Refer to CLOCK, T-
ON, T-OFF bu
ttons)
blowing fan at fixed angle. Horizontal lou ver will
send air at the fixed angle.
T-ON T-OFF
T-ON button
"T-ON" button can set the time for timer on. After
button to cance l it.
pressing this button, " " icon disappears and
the word "ON" on remote co ntroller blinks. Press
" " or
" " button to adjust T-ON setting. After
each pressing " " or " " button, T-ON sett i ng
will increase or decrease 1min. Hold " " or " "
button, 2s later, the time will change quickly u
ntil
reaching your required time. Press "T-ON
" to
confirm it. The word "ON" will
stop blinking. "
"
icon resumes displaying. Cancel T-ON: Under the
condition that T-ON is sta rted up, press "T-O
N"
button to cancel it.
T-OFF button
"T-OFF" button can set the time for timer off. Af-
ter pressing this button, " " icon disappears
and the word "OFF" on remote controller blinks.
Press " " or " " button to adjust T-OFF setting.
15
t urn to quick COOL or quick HEAT mode. " "
icon is dis played on remote controller. Press this
button again to exit turbo func tion and " " icon
will disappear. If start this function, the unit will
run at super-high fan speed to cool or heat quickly
so that the ambient temperature approaches the
preset temperature as soon as possible.
After each pressing " " or " " butto n, T-OFF
setting will increase or decrease 1min. Hold " "
or " " bu tto n, 2s later, the time will change qui-
ckly until reaching your required time. Press "T-
OFF" word "OFF" will stop blinkin g.
" " icon
resumes displaying. Cance l T-OFF. Under the
condition that T-OFF is started up, press "T-OFF"
To Next Page
Loading...
