Grundfos CIM 250 - Pit Status Register Block

English (GB)
24
9.6 Pit status register block
Registers in this block can be read by means of function codes
0x03 and/or 0x04. It is not possible to write to these registers.
Unless otherwise stated, the data type used for counters and
scaled values is always an unsigned integer.
Address Register name Scale Description
00201
AcknowledgeRegister
Bit 0: AckResetAlarm
Bool
Indicates if a ResetAlarm control bit was acknowledged by the device.
This bit is only active if AutoAckControlBits (register 00005, bit 0) is set
to "0".
0 = Not acknowledged
1 = Acknowledged.
AcknowledgeRegister
Bit 1: AckSetRtc
Bool
Indicates if a SetRtc (real-time clock) control bit was acknowledged by
the device. This bit is only active if AutoAckControlBits (register 00005,
bit 0) is set to "0".
0 = Not acknowledged
1 = Acknowledged.
AcknowledgeRegister
Bit 2: AckResetEventLog
Bool
Indicates if a ResetEventLog control bit was acknowledged by the
device. This bit is only active if AutoAckControlBits (register 00005, bit
0) is set to "0".
0 = Not acknowledged
1 = Acknowledged.
AcknowledgeRegister
Bit 3: AckInterlockPit
Bool
Indicates if an InterlockPit control bit was acknowledged by the device.
This bit is only active if AutoAckControlBits (register 00005, bit 0) is set
to "0".
0 = Not acknowledged
1 = Acknowledged.
AcknowledgeRegister
Bit 4: AckAutoPit
Bool
Indicates if an AutoPit control bit was acknowledged by the device. This
bit is only active if AutoAckControlBits (register 00005, bit 0) is set to
"0".
0 = Not acknowledged
1 = Acknowledged.
AcknowledgeRegister
Bit 5: AckCallBack
Bool
Indicates if a CallBack control bit was acknowledged by the device. This
bit is only active if AutoAckControlBits (register 00005, bit 0) is set to
"0".
0: Not acknowledged
1: Acknowledged.
AcknowledgeRegister
Bit 6: ResetUserDefCounter1
Bool
Indicates if a ResetUserDefCounter1 control bit was acknowledged by
the device. This bit is only active if AutoAckControlBits (register 00005,
bit 0) is set to "0".
0 = Not acknowledged
1 = Acknowledged.
AcknowledgeRegister
Bit 7: ResetUserDefCounter2
Bool
Indicates if a ResetUserDefCounter2 control bit was acknowledged by
the device. This bit is only active if AutoAckControlBits (register 00005,
bit 0) is set to "0".
0 = Not acknowledged
1 = Acknowledged.
AcknowledgeRegister
Bit 8: ResetUserDefCounter3
Bool
Indicates if a ResetUserDefCounter3 control bit was acknowledged by
the device. This bit is only active if AutoAckControlBits (register 00005,
bit 0) is set to "0".
0 = Not acknowledged
1 = Acknowledged.
AcknowledgeRegister
Bit 9: CallBackTest
Bool
Indicates if a CallBackTest control bit was acknowledged by the device.
This bit is only active if AutoAckControlBits (register 00005, bit 0) is set
to "0".
0 = Not acknowledged
1 = Acknowledged.
AcknowledgeRegister
Bit 10: RelayPulse
Bool
Indicates if a RelayPulse control bit was acknowledged by the device.
This bit is only active if AutoAckControlBits (register 00005, bit 0) is set
to "0".
0 = Not acknowledged
1 = Acknowledged.
Pumpland.ru