To Next PageTo Next Page
Need help?Do you have a question about the Gyroor Kids and is the answer not in the manual?
Measure elbow and wrist circumference for proper fit.
Measure knee circumference for proper fit by following instructions.
Important usage guidelines, limitations, and damage inspection for protective gear.
The Gyroor Kids Protective Gear Set is specifically designed to offer safety and comfort for children engaging in various sports activities. This protective gear is an essential accessory for young riders of roller skates, skateboards, scooters, hoverboards, and karts, providing a crucial layer of protection against potential injuries.
The primary function of the Gyroor Kids Protective Gear Set is to safeguard children's knees, elbows, and wrists during sports and recreational activities. It is engineered to absorb impact and reduce the risk of abrasions, cuts, and more severe injuries that can occur from falls or collisions. The set includes knee pads, elbow pads, and wrist guards, each tailored to protect specific vulnerable areas of a child's body. While the gear significantly reduces the likelihood of injury, it is important to understand that it cannot completely prevent all sports-related injuries. Therefore, adult guidance is recommended during fitting and use to ensure optimal protection.
The Gyroor Kids Protective Gear Set is designed for ease of use and a secure fit. Each piece of protective gear features an adjustable Velcro design, allowing for a customized and snug fit that can accommodate growing children. This adjustability is key to ensuring that the gear stays in place during dynamic movements, providing continuous protection.
To wear the protective gear, users should unfold the Velcro straps, position the gear on the appropriate body part (knees, elbows, or palms), adjust the elasticity to a comfortable level, and then secure the Velcro. The set includes two knee pads, two elbow pads, and two wrist guards, ensuring comprehensive protection for both sides of the body. The wearing diagram illustrates how each component should be correctly positioned: knee pads on the knees, elbow pads on the elbows, and wrist guards on the wrists. The elastic band tied and sleeve wear methods further enhance the secure fit and comfort of the gear.
It is crucial to select the correct size of protective gear for effective protection. The manual provides detailed instructions on how to measure the circumference of a child's knees, elbows, and wrists to determine the most suitable size. For elbow and wrist measurements, users should measure the circumference 2.5 inches above and below the elbow center, and from the center of the wrist. For knee measurements, the circumference should be taken around the lower leg, 2.8 inches (7cm) above and below the patella, with the knee joint flexed at approximately 30 degrees. If the purchased size is not suitable, Gyroor offers a free replacement service, emphasizing their commitment to customer satisfaction and safety.
The protective gear is specifically intended for ordinary children's roller skating, skateboarding, scooters, hoverboards, and karts. It should not be used for other purposes, as its design and protective capabilities are optimized for these specific activities. Users are also advised against modifying the protective gear in terms of structure, color, or any other aspect, as such alterations can compromise its protective effect. Any dirt, alteration, or improper use may negatively impact the gear's performance.
Before each use, it is essential to check the protective gear for any signs of damage. The gear should be discarded and replaced if any of the following conditions are observed: dents, cracks, deep scratches, or discoloration on the shell; compaction or holes in the filler under the shell; straps that are no longer fastened, excessively stretched, torn, or frayed; or if the protector no longer fits or covers the expected area. In the event of a major impact, the protective gear should be inspected for damage, and if severely damaged, it should be immediately replaced.
Maintaining the Gyroor Kids Protective Gear Set is straightforward, ensuring its longevity and continued effectiveness. The cleaning method is designed to be simple yet thorough, preserving the integrity of the materials.
To clean the protective gear, users should first wipe it with a soft, damp cloth. For stubborn stains, the gear can be soaked in soapy water before being cleaned with a brush. It is important to avoid using strong detergents such as bleach or lye, as these can damage the materials and compromise the protective qualities of the gear. After cleaning, the gear should be placed in a well-ventilated area to dry, away from direct sunlight, which can degrade the materials over time.
For any after-sales service inquiries or if the protective gear size is unsuitable, customers can contact Gyroor via their official email at support@gyroorboard.com for assistance with replacements. Additionally, users can stay updated on news about Gyroor hoverboards by scanning the provided QR code to access the "Gyroorboard" Messenger.
General| Product Type | Kids Helmet |
|---|---|
| Intended Use | Skateboarding, Scooter Riding |
| Color Options | Multiple colors available |
| Certification | CPSC Certified |
| Ventilation | Multiple vents for airflow |
| Chin Strap | Adjustable chin strap |
