Habitat Okko - User Manual

To Next Page

Okko - 05/2016 1

Okko

Alarm clock

Réveil

Despertador

Wecker

953115

Indoor use only.

Information to be kept.

Read carefully the instruction sheet before first use.

Characteristics

Sold with a safety class II transformer IP20.

Primary : 220-240V~, 50/60Hz

Secondary : 6V~, 300mA

General instructions

Transformers and power supplies are not intended to be used

as toys, and use of these products by children must be under the

strict supervision of parents.

To prevent unnecessary drain on the battery, install only after

connecting the alarm clock to AC power.

Replace the batteries when the movement is slowed, the sound

or display is distorted / light intensity reduced.

The batteries should be inserted by the polarity and the terminals

should not be short-circuited.

Do not recharge non-rechargeable batteries.

Do not mix batteries and accumulators new and used.

Do not mix alkaline batteries with saline batteries.

Only use the recommended type of batteries.

Remove used batteries or accumulators from the product.

Remove the batteries while not using the unit for long periods.

Clock

1. Alarm on indicator

2. Snooze button

3. Hour set button

4. Minute set button

5. Time set button

6. Alarm set button

7. Alarm ON/OFF button

8. Battery compartment

To operate clock

Blinking display/Alarm on indicator

When the clock plugged in, the display will blink on and off

meaning the incorrect time is being displayed. In this case, it’s

very important to always check the time displayed. When the

alarm indicator is displayed, the alarm will sound at the time set.

Set the time

Press and hold the time set button and the hour set button until

the correct hour is displayed then release the hour set button and

press the minute set button until the correct minute is displayed.

Set the alarm

Press and hold on the alarm set button and the hour set button

or minute set button as above.

To operate the alarm

Slide the alarm ON/OFF switch to the ON position. the alarm will

sound at the time set. to shut off the alarm slide the alarm

ON/OFF switch to the OFF position.

Snooze the alarm

Press the top of the case to activate snooze for 9 minutes.

Battery back up

Insert one 9V battery into the battery compartment located to the

bottom of the clock. The battery will hold the alarm and time

settings until power is restored. If there is no battery and the

power is interrupted, the display will flash and the alarm and time

will need to be reset.

Maintenance

Use a soft cloth or paper towel to clean the clock. Do not use any

corrosive cleaning solution to clean the clock. Keep the clock

clean and dry to avoid any problems.

If you have any comments or suggestions regarding this product,

assembly instructions or service received, please enquire at your

nearest store or contact us on our website at: www.habitat.eu or

write to this address: HABITAT FRANCE SERVICE CLIENT-42/44

RUE DU FAUBOURG ST ANTOINE 75012 PARIS-FRANCE

Need help?

Do you have a question about the Habitat Okko and is the answer not in the manual?

The Okko 953115 is an alarm clock designed for indoor use, offering both timekeeping and alarm functionalities with a battery backup feature. It comes with a safety class II transformer, IP20 rated, for power supply.

Function Description

The primary function of the Okko 953115 is to display time and provide an alarm. When plugged in, the display will blink if the time is incorrect, prompting the user to set the correct time. An alarm indicator will be displayed when the alarm is set to sound. The clock allows for setting both the current time and a specific alarm time. A snooze function is also available, which, when activated, postpones the alarm for 9 minutes. In case of a power interruption, a 9V battery can be inserted into the battery compartment to maintain the alarm and time settings, preventing the need for a full reset once power is restored. Without the battery backup, a power interruption will cause the display to flash, and both the alarm and time will need to be reset.

Important Technical Specifications

Model Number: 953115
Power Supply:
- Primary: 220-240V~, 50/60Hz
- Secondary: 6V~, 300mA
Transformer: Safety class II, IP20 rated
Battery Backup: Requires one 9V battery (not included)
Snooze Duration: 9 minutes
Usage Environment: Indoor use only

Usage Features

The Okko alarm clock is designed for straightforward operation with several dedicated buttons for setting time and alarm.

Setting the Time: To set the current time, the user needs to press and hold the "Time set button" (5) along with the "Hour set button" (3) until the correct hour is displayed. After releasing the "Hour set button," the "Minute set button" (4) should be pressed until the correct minute is displayed.

Setting the Alarm: Setting the alarm follows a similar procedure. The user must press and hold the "Alarm set button" (6) along with either the "Hour set button" (3) or the "Minute set button" (4) to set the desired alarm time.

Operating the Alarm: To activate the alarm, the "Alarm ON/OFF switch" (7) should be slid to the ON position. The alarm will sound at the set time. To turn off the alarm, the switch should be slid to the OFF position.

Snooze Function: When the alarm sounds, pressing the "Snooze button" (2) on the top of the case will activate the snooze function, delaying the alarm for 9 minutes.

Battery Backup: A 9V battery can be inserted into the "Battery compartment" (8) located at the bottom of the clock. This battery will preserve the alarm and time settings during a power outage. If there is no battery and power is interrupted, the display will flash, and the time and alarm settings will need to be reset.

General Instructions for Battery Use:

Batteries should only be installed after connecting the alarm clock to AC power to prevent unnecessary drain.
Replace batteries when the movement slows, sound distorts, or display intensity reduces.
Insert batteries with correct polarity, and ensure terminals are not short-circuited.
Do not recharge non-rechargeable batteries.
Do not mix new and used batteries or accumulators.
Do not mix alkaline batteries with saline batteries.
Use only the recommended type of batteries.
Remove used batteries or accumulators from the product.
Remove batteries if the unit will not be used for long periods.
Transformers and power supplies are not intended as toys, and their use by children must be under strict parental supervision.

Maintenance Features

Maintaining the Okko alarm clock is simple and requires minimal effort to ensure its longevity and proper functioning.

Cleaning: Use a soft cloth or paper towel to clean the clock.
Avoid Corrosive Solutions: Do not use any corrosive cleaning solutions, as these can damage the device.
Keep Clean and Dry: To prevent problems, it is important to keep the clock clean and dry.

For any comments, suggestions, or service inquiries regarding the product or assembly instructions, customers are advised to contact their nearest Habitat store or visit the Habitat website (www.habitat.eu). Alternatively, they can write to Habitat France Service Client at 42/44 Rue du Faubourg St Antoine, 75012 Paris, France. For German customers, the address is Habitat Deutschland GmbH, Kundenservice, Berliner Allee 15, 40212 Düsseldorf. For Spanish customers, the address is Habitat España, Compañia de Equipamientos del Hogar, Habitat, S.A., Avda. Diagonal, 415, 08006 Barcelona.

Habitat Okko Specifications

General

Brand	Habitat
Model	Okko
Category	Alarm Clock
Language	English