Function menu operation process
Memory channel (MEM-CH) - Menu 33
In channel mode or standby mode, press [MENU] + [3 SAVE] + [3 SAVE], the
screen will display: Save channel
Press the [MENU] key to enter, press the [UP]/[DOWN] key to select the desired
channel number, and then press the [MENU] key to confirm storage. There will be
a voice prompt to confirm, and press the [EXIT] key to exit.
When the current working channel is in channel mode (MR), all parameters of the
channel except channel name and scan addition will be copied to the stored
channel.
When the current working channel is in frequency mode (VFO), you can set
different frequency differences, frequency difference directions and other channel
parameters and then store the channel, so that you can set channels with different
frequencies in the same frequency band or different frequency bands.
For example, "Save the receiving frequency to 450.025MHz, the receiving analog
tone to 67.0Hz, and the transmitting frequency to 460.025MHz to the 10th channel.
1. In the frequency mode, enter the 450.025 frequency point, press [MENU] +
[1 STEP][5 ROGER] to enter the sub-tone receiving setting function, press the
[UP]/[DOWN] key to select 67.0Hz, press [MENU] confirm.
2. Press [MENU] + [2 SQL] + {4TXP] to set the frequency difference to 10.000MHz,
and press to set the direction of the frequency difference to positive frequency
difference +.
3. Press [MENU] + [3 SAVE] + [3 SAVE] to enter the storage channel. Select the
10th channel and press the [MENU] key to confirm and then return to the
standby state.
In the standby state, press the [MENU] + [3 SAVE] + [3 SAVE] keys to enter
channel storage. At this time, the LCD displays: Enter the hundreds, tens, and
ones digits of the channel number to be saved in sequence, and then press the
[MENU] key. confirm.
Notice
When the selected channel is an empty channel, the font of the channel number
is blue; if the selected channel is a channel with originally set parameters, the
font of the channel number is dark red.
15
Function menu operation process
Channel Delete (DEL-CH) - Menu 34
In standby mode, press [MENU] + [3 SAVE] + [4 TXP], the screen will display:
Channel Delete
Press the [MENU] key to enter , press the [UP]/[DOWN] key to select the channel
number to be deleted or directly enter the channel number to be deleted and press
the [MENU] key to confirm, press the [EXIT] key to return to the standby state.
Special Note
»The first channel can’t be deleted.
» When the selected channel is an empty channel, the font of the channel number
is blue; if the selected channel is a channel with originally set parameters, the
font of the channel number is dark red.
Relay switch (RPT-SW) - Menu 35
This function can turn on and off the relay function for the walkie-talkie. When the
relay function is turned on, other relay settings will take effect.
In standby mode, press [MENU] + [3 SAVE] + [5 ROGER], the screen will display:
Press [MENU] to enter relay switch, press [UP/DOWN] to select ON/OFF Then
press the [MENU] key to confirm, and press the [EXIT] key to return to the standby
state.
Relay receipt sound ((RPT-RCT)) - Menu 36
The relay acknowledgment tone refers to the relay station offline confirmation tone
received when the intercom relays the transfer signal and is offline.
In standby mode, press [MENU] + [3 SAVE] + [6 TOT] keys, the screen will display:
Transfer receipt sound
Press the [MENU] key to enter, press the [UP]/[DOWN] key to select ON (on)/OFF
(off) and press the [MENU] key to confirm, press the [EXIT] key to return to the
standby state.
Battery voltage (V-BAT) - - Menu 37
In the standby state, press the [MENU] + [3 SAVE] + [7VOX] keys, the screen will
display: display the current battery voltage, press the [EXIT] key to return to the
standby state.
Scan to add (SCAN-ADD) - Menu 38
Scan Add (SCAN-ADD) is a function that determines whether the current channel
participates in scanning when channel scanning is started.
16
Function menu operation process
Therefore, this function setting can only be set for the current channel in channel
mode, and the setting is invalid in frequency mode. In standby mode, press
[MENU] + [3 SAVE][8 W/N] keys, the screen will display: Scan to add
Press the [MENU] key to enter, press the [UP]/[DOWN] key to select ON (on)/OFF
(off) and press the [MENU] key to confirm, press the [EXIT] key to return to the
standby state.
Note: The walkie-talkie works in cross-segment relay or relay/transmitter mode,
and this function is prohibited.
Priority Channel (PRI_CH) - Menu 39
In standby mode, press [MENU] + [3 SAVE] + [9 VOICE], the screen will display:
Priority channel switch, press [MENU] to enter, press [UP/DOWN] to select ON/
OFF Then press the [MENU] key to confirm, and press the [EXIT] key to return
to the standby state.
Sometimes it may be necessary to check for activity on a preferred frequency while
listening to other frequencies. In this case, the priority scan function can be used.
Example: Scan 6 common channels CH1, CH2, CH3, CH4, CH5, CH6, among
which CH6 is set as the priority channel. Then the scan is: CH1→CH6→CH2→
CH6→CH3→CH6→CH4→CH6→ CHS5→CHS6 If the walkie-talkie detects a
signal on the "priority channel", it will call out the frequency. The priority channel
can be selected through our frequency writing software.
Priority Scan (PRI_SCN) - Menu 40
Whether to add a channel to the priority scanning channel in the current standby
state, press [MENU] + [4 TXP] + [0] keys, the screen will display: Priority scanning
Press the [MENU] key to enter, press the [UP]/[DOWN] key to select ON (on)/OFF
(off) and press the [MENU] key to confirm, press the [EXIT] key to return to the
standby state.
Scramble Switch (RP-SW) - Menu 41
When the frequency is the same as that of others, the scrambling function can be
turned on to prevent others from hearing the call content. There are 8 sets of
scrambling codes to choose from.
In standby mode, press [MENU] + [4 TXP] + [1 STEP] keys, the screen will
display: Scramble switch
Press the [MENU] key to enter, press the [UP]/[DOWN] key to select the required
scrambling code, press the [MENU] key to confirm, and return to the standby state.
17
Function menu operation process
Companding switch (YK-SW) - Menu 42
In standby mode, press [MENU] + [4 TXP] + [2 SQL] keys, the screen will display:
Companding switch
Press the [MENU] key to enter, press the [UP]/[DOWN] key to select the required
scrambling code, press the [MENU] key to confirm, and return to the standby state.
Fast Scan - - Menu 43
In standby mode, press [MENU] + [4 TXP] + [3 SAVE] keys, the screen will display:
Scanning...
Scans for nearby transmitters, displays the frequency and subtone or digital subtone
signaling of the received signal, and provides save or return exit options.
Version number (VERSION) - - Menu 44
In the standby state, press the [MENU] + [4 TXP] + [4 TXP] keys. The screen will
display: the current firmware version number. Press the [EXIT] key to return to
the standby state.
Reset (RESET) - Menu 45
Reset function parameters (VFO), reset all function settings and restore factory
function parameter values, but channel parameters are not reset.
Resent function parameters (ALL), reset all function settings and channel param-
eters, and return the factory function parameter values.
In standby mode, press [MENU] + [4 TXP] + [5 ROGER] keys, the screen will
display:
Press the [MENU] key to enter, press the [UP]/[DOWN] key to select the required
parameters and press the [MENU] key to confirm. The screen displays:
Reset settings
The handheld device will perform function parameter reset(VFO)/all parameter
reset (ALL). After the reset is completed, the handheld device will automatically
restart and return to the standby state.
18
To Next Page
Loading...