LESLIE SWITCH
Owner’s Manual
Attaching the CU-1 to the keyboard
ank you and congratulations on your purchase of the Ham-
mond CU-1 Leslie switch. e lever switch on the “Half-
Moon” shaped CU-1 unit is used to control the Leslie e ects
just like on the original B-3. Please read the installations in-
structions carefully before you install the CU-1.
Purchased items:
CU-1 unit
(w/2 Thumb screws) ..........1
Spacer (thick) .......................1
Spacer (thin) .........................1
Setting up to allow the CU-1
For your safety, please operate your Hammond prod-
uct on a level, stable surface.
Line up the screws attached to the CU-1 unit with the pair of chosen
holes located on the bottom side of the front rail and securely tighten
these screws.
NOTE: Do not place the keyboard with the CU-1 unit attached onto a at
desk type surface. Since the CU-1 extends past the bottom of the
keyboard, the CU-1 unit and front rail of the keyboard could be
seriously damaged.
NOTE: Before placing your XK-3/3C into an ATA keyboard type case, make
sure you remove the CU-1 unit rst.
2. Connecting to the equipment
#920, A-162, A-405, SK2, XK-1C, XK-3, XK-3C, XLK-3
Insert the plug on the CU-1 into the equipment labeled “Foot Switch”
jack.
XK-5, XLK-5
Insert the plug on the CU-1 into the equipment labeled “CU-1” jack.
For other compatible model, see owner’s manual of your instrument
which attach the CU-1 for detail.
#920, A-162, A-405, XK-3, XK-3C, XLK-3
Turn on the equipment, touch the [MENU], [4]Control and choice
the “FOOT SW” page using [PAGE] buttons.
Select “CU-1” using [VALUE] buttons.
SK2, XK-1C
Turn on the equipment, touch the [MENU], [][][]Control and
choice the “FOOT SW” page using [] []buttons.
Select “CU-1” using [VALUE] knob.
XK-5, XLK-5
No operation required.
For other compatible model, see owner’s manual of your equipment
how to set up the CU-1.
Playing with your CU-1 Switch
#920, A-162, A-405, XK-3, XK-3C
CHORALE: e Leslie e ect is “On”, rotation mode is “Slow.”
TREMOLO: e Leslie e ect is “On”, rotation mode is “Fast.”
STOP: 1) e rotation stops, the Leslie e ect is still “ON”, if the
[BRAKE] button is “On” (XK-3/3C) or O Mode is at “Brake”
(#920, A-162, A-405).
2) e Leslie e ect is “O ”, rotation continues, if the [BRAKE]
button is “O ” (XK-3/3C) or O Mode is at “ rough” (#920,
A-162, A-405).
It takes a moment for the equipment detecting STOP position,
to make the switching between CHORALE and TREMOLO
smoothly.
SK2, XK-1C, XK-5
CHORALE: e rotation mode is “Slow.”
TREMOLO: e rotation mode is “Fast.”
STOP: e rotation stops. It takes a moment for the equipment de-
tecting the STOP position, to make the switching between
CHORALE and TREMOLO smoothly.
It switches only the rotation. To switch “On” or “Bypass” the
Leslie e ect (switch Rotary or Stationary channel), press the
[BYPASS] button.
NOTE: On newer Hammond products, the speeds of the Leslie can also
be selected by means of a kick switch on the expression pedal or a
switch button on the product itself. Thus the selected speed on the
CU-1 unit may occasionally not match the action speed (slow-fast-
o ) of the Leslie. If this occurs, simply move the lever switch on the
CU-1 to the adjacent position and the actual rotor speed will then
match the CU-1 selection.
Manufacturer:
SUZUKI MUSICAL INSTRUMENT MFG. CO., LTD.
25-12, Ryoke 2 Chome, Naka-ku,
Hamamatsu 430-0852 (Shizuoka)
JAPAN
1. Attaching the CU-1 unit.
SK2, XK-1C, XK-3, XK-3C (Thin bottom of the Keyboard)
Remove the protective paper from the adhesive tape on the thick spac-
er, and attach the spacer to the CU-1 unit as shown above.
XLK-3, XLK-5 (Middle bottom of the Keyboard)
Remove the protective paper from the adhesive tape on the thin spac-
er, and attach the spacer to the CU-1 unit as shown above.
#920, A-162, A-405, XK-5 (Deep bottom of the Keyboard)
No spacer is needed for mounting the CU-1 Unit.
To Next Page
General