Handife Q1P-CX49-380 User Manual (English)

Questions and Answers:

M
Martin WilliamsAug 12, 2025
Why is there little or no material flow from my Handife Paint Sprayer?
- J
  Jennifer GarciaAug 12, 2025
  There are several reasons why your Handife Paint Sprayer might have little to no material flow: * The nozzle could be clogged, so clean the nozzle. * The suction tube might be clogged, so clean the suction tube. * The material volume setting may need adjustment, so adjust the nut. * The suction tube could be loose, so adjust the suction. * The material might be too thick, so check the viscosity. * The container might be loose, so tighten the container.
C
Christina BakerAug 16, 2025
What to do if my Handife Paint Sprayer material is leaking?
- K
  Kaitlyn Johnson DVMAug 16, 2025
  If the material is leaking from your Handife Paint Sprayer, it could be due to: * A loose nozzle, in which case you should tighten it. * A broken nozzle, which means you should replace it. * A broken nozzle seal, which also requires replacement.
J
Joshua BarnesAug 20, 2025
Why does my Handife Paint Sprayer spray pulsate?
- K
  Kristen OrozcoAug 20, 2025
  If your Handife Paint Sprayer's spray pulsates, it could be because: * The material in the container is running out, so refill it. * The material is too thick, so check the viscosity.
K
kriddleAug 25, 2025
Why is there too much over-spray with my Handife Paint Sprayer?
- J
  jonestanyaAug 25, 2025
  Too much over-spray from your Handife Paint Sprayer can occur if: * The spray distance is too far, so reduce the spray distance. * There is too much material in the container, so refill the container.
M
Melissa MullinsAug 28, 2025
What to do if the droplet size is too large with my Handife Paint Sprayer?
- T
  Timothy BernardAug 28, 2025
  If the droplet size is too large when using the Handife Paint Sprayer: * The viscosity may be too high, so thin the material. * The volume may be too large, so adjust the nut. * The nozzle may be clogged, so clean it. * The pressure may not be enough, so tighten the container.
A
Angela MartinAug 31, 2025
Why is the spray pattern running or sagging when using my Handife Paint Sprayer?
- K
  Kelly JacksonAug 31, 2025
  If the spray pattern runs or sags when using the Handife Paint Sprayer, it may be because you are spraying too much material. To resolve this, move the spray gun smoothly.
J
Jennifer WheelerSep 4, 2025
Why does my Handife Paint Sprayer create a large spray spot?
- W
  Wesley RamosSep 4, 2025
  A large spray spot from your Handife Paint Sprayer is caused by the spray distance being too close. Move the gun away from the surface and reduce paint flow.
T
Tara TaylorSep 8, 2025
Why is the spray pattern light and splotchy with my Handife Paint Sprayer?
- M
  Michael AndersonSep 8, 2025
  If the spray pattern is light and splotchy with your Handife Paint Sprayer, it's likely because you are moving the spray gun too fast. Adjust the material flow or decrease the movement speed of the spray gun.

Handife Q1P-CX49-380 Specifications

General

Model	Q1P-CX49-380
Category	Paint Sprayer
Power Source	Electric
Power	380W
Max Pressure	3000 PSI
Maximum Flow Rate	800 ml/min
Nozzle Size	2.5 mm
Voltage	220V
Frequency	50/60 Hz

Handife Q1P-CX49-380 User Manual

Table of Contents

Questions and Answers:

Handife Q1P-CX49-380 Specifications