CONTROL AND FUNCTIONS
Front
Panel
harman/kardon
AVR70
D Information Display: This dis-
play delivers messages and status
indications to help you operate the
receiver. Refer to the separate dia-
gram for a complete explanation of
the FL display.
f.l
Remote Sensor Window:
The
sensor behind this window receives
infrared signals from the remote con-
trol. Aim the remote at this area and
do
not block or cover it unless an
external remote sensor
is
installed.
I!)
AM/FM
Tuner
Mode Selection:
Press this button once to select the
tuner. Press it again
to
switch
between
FM,
MW and
LW.
El
CO:
Press this button to select
the CD player.
Ii)
Tape1/Monitor: Press this button
to select Tape One as the input
source. A red
LED
above the button
will illuminate to indicate that the
Tape Monitor has been selected.
Iii
Tape
2:
Press this button to select
Tape
2.
Ii
Video
Sources:
Press any of
these buttons to select a video input
source.
Ii)
Aux:
Press this button to select
the source connected to the front
panel
Aux
jacks.
Ii]
Display:
Press this button to
turn off the front panel FL display.
The.DISP indicator will illuminate
to remind you that the unit is still
turned on.
ml
050
(On
Screen Display):
Press the button briefly
to
display a
system status report on your video
screen. Press and hold to change
the video standard.
W
Delay:
Press this button to
increase the delay to the rear (sur-
round) channels.
VISllAU>
rv
LO
VCR
12
AL/Xfilill~~@!rn
~
1:-:l.i
P R O L O G I C
;,
~
I~~~~
IE
Mode:
Press these buttons to
scroll up
.A.
or down
,r
through the
list of available surround modes.
IE]
P-Set:
Press these buttons to
manually scroll up
.A.
or down
,r
through the
FM,
LW
or AM stations
programmed into the receiver's pre-
set memory.
IE
P-Scan:
Press this button to
automatically scan through the
FM
or AM stations preset into the receiv-
er's memory. Press the button again
to stop the scan when the tuner
is
at
the desired station.
ml
Tune:
Press these buttons to
manually scan
up
..., or down
,r
through the
FM
or AM bands.
Im
Mute:
Press this button to cut the
output to the speakers. Press it
again to return to the previous vol-
ume level.
ffi
Volume
Control:
Turn
the knob
clockwise to increase volume, coun-
terclockwise to decrease the vol-
ume. Note that approximately two
revolutions of the knob are required
to
go
from no output to maximum
volume.
ml
Power:
press
this
button
once
to
turn
the
unit
on
or
off.
In
order
to
use
the
remote
control
to
turn
the
unit
on
the
power
switch
must
be
pressed
once,
and
then
the
unit
must
be
turned
off
via
the
remote.
The
LED
indicator
light
surrounding
the
power
switch
will
glow
amber
when
the
unit
is
In
the
Standby
mode
and
green
when
the
unit
is
on.
ml
Headphone
Jack:
Plug standard
stereo headphones into this jack for
private listening.
NOTE: When the headphones are
in
use the output to the speakers
is
muted and the surround mode
is
automatically switched to STEREO.
When the headphones are removed
from the jack, sound to the speakers
is
restored and the unit returns to the
previous sound mode.
Im]
Memo:
The memo button
is
used
to enter stations to the tuner's preset
memory
in
either the manual or auto-
matic modes. It
is
also used
in
clear-
ing the memory and entering the
sleep timer period.
fll
Clear:
The clear button
is
used
to cancel tuning, memory input or
when clearing the unit's memories.
~
FM
Mode:
Press this button
to select the tuning mode for
FM
stations.
fJl
RDS
Display:
When a station
transmitting
RDS
data
is
tuned,
press this button to view the tuning
frequency.
f:m
RDS
AF:
The button
is
used to
search for stations transmitting a
specific programme type that offers
better reception than the currently
tuned station.
f1il
RDS
PTY:
Press this button to
view the programme type (PTY)
when an
RDS
station is tuned.
It
is
also used to initiate a search for
RDS
stations transmitting a specific pro-
gramme type.
!ml
Bass:
This knob adjusts the tone
of low frequency sounds. Turn it
to
the right to boost bass frequencies
or to the left to
cut. bass frequencies.
f,i
Treble:
This knob adjusts
the tone of high frequency sounds.
Turn
it to the right to boost high
frequencies or to the left to cut high
frequencies.
f:m
Balance: This knob adjusts the
balance between the front left and
right speakers.
~
Front
Panel
Inputs:
Audio or
Video sources connected to these
jacks may be selected
by
pressing
the
Aux
button Ii).
•[I
ONLY
I
O
Use/LE
the operati
control.
Slii
operation.
the remote
f)
Main
F
buttons to
osourc,
of these
bL
source tha
through
th,
is
selectec
and numer
also transr
to control t
C,Sourc,
tons
to
cor
source
de
1
O
SurroI
Press one
a surrounc
tening ses
0Mainl
control the
all channe
neously.
To Next Page
Loading...
