Harman Kardon AVR7000 - Front Amp Section Data; Detailed Specifications

DETAILED SPECIFICATION FOR RECEIVER AVR7000 (120V)
PARAMETERS
Measuring methods are based on IHF and IEC standard 268-3
Measurement conditions,unless otherwise noted :
Output resistive load = (8) ohms / All channels loaded.
Tone Off or Tone(Bass,Treble), Balance, EQ control : Center Position , Other SW's : OFF, Volume:Max
Nominal input level : 200mV for general purpose inputs
Power figures should be kept minimum 10min., between 15 and 35
o
C
.
Terminator : 1kohm for general purpose inputs
All Voltage Measurements are made with RMS detector, unless otherwise specified.
Filter : IHF-A filter
R/O = Rated Output, which is 100 W into 8 ohm resistive load, for both Stereo and 6 CH DIRECT inputs.
UUT= Unit Under Test.
Power supply : 120 V , 60 Hz
D
FRONT AMP SECTION
*SUB-WOOFER SPKR:NO *SPKR LEVEL:ALL 0dB
NO
DESCRIPTION
Y/N
INPUT
FREQ.
REMARK
UNIT
LIMIT
NOMINAL
1
INPUT SENSITIVITY Y CD 1kHz To obtain rated Power mV 200+/-30
200+/-20
Y 6 CH DIRECT 1kHz To obtain rated Power mV
2
CHANNEL BALANCE
Y
6 CH DIRECT 1kHz
Vin=100mV, Vol at Max TO -40dB
dB +/-3 +/-2
Y 1kHz Vin=100mV, Volt at -40 TO -60dB dB +/-6 +/-4
3
DAMPING FACTOR Y 6 CH DIRECT 1kHz
Zout at a current level equivalent to 10
dB below rated Power current level. 20-
20kHz, 8 ohm load
>100
4
HICC Y 6 CH DIRECT 10 KHz
10 KHz single cycle sine impulse. 1
impulse/sec. Using 0.1 ohm, 1%, 250
W, non inductive load
A >60
>65
5 RESIDUAL NOISE Y
Should be met
by all Stereo
Inputs
1kHz
VOL at min. 10Hz-22KHz BW, peak
detector, all inputs terminated w/ 1
Kohm
mVpk
<1.2mV
<1.0mV
Y
Should be met
by all Stereo
Inputs
1kHz
VOL at max. 10Hz-22KHz BW, peak
detector, all inputs terminated w/ 1
Kohm
mVpk
<3mVrms
<1.5mVrms
Y
Should be met
by all Stereo
Inputs
1kHz
VOL at max. 10Hz-22KHz BW, RMS ,
non-weighted, all inputs terminated w/
1 Kohm
mVrms
<1mVrms
<0.75mVrms
Y
Should be met
by all Stereo
Inputs
1kHz
VOL at max. 10Hz-22KHz BW, RMS ,
'A Weighted', all inputs terminated w/ 1
Kohm
mVrms
<0.7mVrms
<0.5mVrms
Y
Should be met
by all Stereo
Inputs
1kHz
VOL at max. 10Hz-22KHz BW, RMS ,
'A Weighted', all inputs left un-
terminated
mVrms
<0.7mVrms
<0.5mVrms
RESIDUAL NOISE Y 6 CH DIRECT 1kHz
VOL at min. 10Hz-22KHz BW, peak
detector, all inputs terminated w/ 1
Kohm
mVpk
<1.2mVrms
<1.0mVrms
Y 6 CH DIRECT 1kHz
VOL at max. 10Hz-22KHz BW, peak
detector, all inputs terminated w/ 1
Kohm
mVpk
<3mVrms
<1.5mVrms
Y 6 CH DIRECT 1kHz
VOL at max. 10Hz-22KHz BW, RMS,
non-weighted, all inputs terminated w/
1 Kohm
mVrms
<1mVrms
<0.75mVrms
Y 6 CH DIRECT 1kHz
VOL at max. 10Hz-22KHz BW, RMS,
'A Weighted', all inputs terminated w/ 1
Kohm
mVrms
<0.7mVrms
<0.5mVrms
Y 6 CH DIRECT 1kHz
VOL at max. 10Hz-22KHz BW, RMS,
'A Weighted', all inputs left un-
terminated
mVrms
<0.7mVrms
<0.5mVrms
6
TOTAL HARMONIC
DISTORTION
Y
Should be met
by all Stereo
Inputs
20Hz-20 KHz, Power
out =Rated Power - 1
dB
Vol at Max, 10 Hz-80KHz Meas BW. % <0.08
<0.05
TOTAL HARMONIC
DISTORTION
Y 6 CH DIRECT
20Hz-20 KHz, Power
out =Rated Power - 1
dB
Vol at Max, 10 Hz-80KHz Meas BW. % <0.08
<0.05
TOTAL HARMONIC
DISTORTION
Y
Should be met
by all Stereo
Inputs
20Hz-10 KHz, Power
out =1 W
Vol at Max, 10 Hz-22 KHz Meas BW. % <0.08
<0.05
TOTAL HARMONIC
DISTORTION
Y 6 CH DIRECT
20Hz-10 KHz, Power
out =1 W
Vol at Max, 10 Hz-22 KHz Meas BW. % <0.08
<0.05
7
CONTINUOUS AVERAGE
POWER: A) Stereo, 8
Ohm load, Fl and FR driven.
Y CD 20 Hz
at 0.1% THD, 10 Hz-80 KHz
measurement BW. Volume at Max.
W >110
>115
Y CD 1kHz
at 0.1% THD, 10 Hz-80 KHz
measurement BW. Volume at Max.
W >110
>115
AVR7000 harman/kardon
5