Harman Kardon Citation II - Page 25

23
Check
( )
( )
Connect a 12˝ white lead to TB1-8 (S), dress around bracket to rear of chassis and connect other end
to T2-16 (S). Route as shown in Pictorial #8.
( )
( )
Connect a 12˝ white lead from TB2-8 (S) to T1-16 (S).
( )
( )
Connect a 33K ohm
½
watt 10% resistor (orange-orange-orange-silver) from V1-2 (S) to TB1-27
(S).
Connect the following wires. Strip
⅜
˝.
( )
( )
Blue 2
½
˝ from V3-7 (NS) to TBl-22 (S).
( )
( )
Blue 2
½
˝ from V3-7 (S) to TB1-18 (S).
( )
( )
Blue 2
¾
˝ from V2-7 (NS) to TB1-29 (S).
( )
( )
Blue 2
¾
˝ from V1-7 (S) to TB 1-25 (S).
( )
( )
Green 3˝ from V1-8 (S) to TBl-23 (S).
( )
( )
Green 2
½
˝ from V2-8 (S) to TB1-32 (S).
( )
( )
Connect a 10K ohm
½
watt 10% resistor (brown-black-orange-silver) from V3-2 (S) to TB1-21 (S).
( )
( )
Connect a 10K ohm
½
watt 10% resistor (brown-black-orange-silver) from V2-2 (S) to TBl-30 (S).
( )
( )
Connect a 4.7K ohm 2 watt 10% resistor (yellow-violet-red-silver) from V2-7 (S) to TBl-33 (S).
Connect the following wires. Strip
⅜
˝.
( )
( )
Blue 2
½
˝ from V6-7 (NS) to TB2-22 (S).
( )
( )
Blue 2
½
˝ from V6-7 (S) to TB2-18 (S).
( )
( )
Blue 2
¾
˝ from V5-7 (NS) to TB2-29 (S).
( )
( )
Blue 2
¾
˝ from V4-7 (S) to TB2-25 (S).
( )
( )
Green 3˝ from V4-8 (S) to TB2-23 (S).
( )
( )
Green 2
½
˝ from V5-8 (S) to TB2-32 (S).
( )
( )
Connect a 10K ohm
½
watt 10% resistor (brown-black-orange-silver) from V6-2 (S) to TB2-21 (S).
( )
( )
Connect a 10K ohm
½
watt 10% resistor (brown-black-orange-silver) from V5-2 (S) to TB2-30 (S).
( )
( )
Connect a 4.7K ohm 2 watt 10% resistor (yellow-violet-red-silver) from V5-7 (S) to TB2-33 (S).
( )
( )
Connect a 33K
½
watt 10 % resistor (orange-orange-orange-silver) from V4-2 (S) to TB2-27 (S).
FINAL WIRING OF THE TERMINAL BOARDS
Refer to Pictorial Diagram #3, Figure D, and install the following components on terminal board 1 (TB1).
Since TB2 is identical, each operation may be performed on both boards at one time.
Center the components between the lugs indicated and bend the leads in a hook shape around the top sec-
tion of the lugs. After soldering, cut off the excess wire.
Check
TB1
TB2
( )
( )
( )
12K ohm 3 watt (value marked on body of resistor) from TBl-17 (S) to TB1-18 (S). Mount
⅜
˝ off terminal board as shown in Figure N.
( )
( )
( )
680K ohm 1 watt 10% resistor (blue-gray-yellow-silver) from TB1-16 (NS) to TB1-46 (NS).
( )
( )
( )
4.7 mmf capacitor (value marked on body of capacitor) from TB1-16 (S) to TB1-46 (S).
( )
( )
( )
100K ohm 12 watt 10% resistor (brown-black-yellow-silver) from TBl-15 (S) to TB1-45 (S).
( )
( )
( )
1 meg ohm
½
watt 10% resistor (brown-black-green-silver) from TB1-44 (S) to TB1-21 (S).
( )
( )
( )
22K ohm
½
watt 10% resistor (red-red-orange silver) from TB1-13 (S) to TB1-43 (NS).
( )
( )
( )
1 meg ohm
½
watt 10% resistor (brown-black-green-silver) from TB1-43 (NS) to TB1-22
(NS).
( )
( )
( )
33K ohm 1 watt 10% resistor (orange-orange-orange-silver) from TB1-12 (S) to TB1-42 (S).
( )
( )
( )
12K ohm
½
watt 10% resistor (brown-red-orange-silver) from TB1-41 (NS) to TB1-24 (NS).
( )
( )
( )
20 mmf capacitor (value marked on body of capacitor) from TB1-43 (S) to TB1-22 (S).