TV MENU, AUX MENU, DIGITAL IN MENU 29
TV MENU, AUX MENU, DIGITAL IN MENU
TV Menu
When the analog left/right audio outputs of a TV,
set-top box, VCR, video game console or any other
audio/video product are connected to the TV Inputs
B on the rear panel, you may listen to that source by
selecting the TV input on your HS 100 by following one
of these steps:
1. If the HS 100 is in the Standby mode, press the
TV Button on the remote to turn on the unit
and go directly to the TV input.
2. If the HS 100 is already on, press the TV Button
on the remote to switch the input, or press the
Source Button 6 on the front panel until the tuner
is the active input.
Since the HS 100 will only select the audio, always
remember to select the corresponding video input
on your display to view the video that corresponds to
the audio.
The TV menu (viewable when your display is set to
the input for the HS 100) enables you to make the
configuration settings for the TV input.
Audio: This line lets you select the surround mode that
is used when the TV input is selected. To change the
default mode, follow these steps:
1. With the TV menu on your video display, press the
M
/
N
/
K
/
L
Navigation Buttons A as needed
so that that the current surround mode to the right of
the Audio line at the top of the menu is highlighted.
2. Press the Enter Button P, and within five sec-
onds press the
M
/
N
Navigation Buttons A so
that the desired surround mode is highlighted.
3. Press the Enter Button P to set that mode as
the new default for the TV input.
Level Adjustment: This line lets you increase or
decrease the input level for the TV input to compensate
for any variations that may be caused by the source
device. In most cases you will not need to adjust this
setting, but if the audio level when the TV input is
selected appears lower or higher than other sources,
follow these steps to make an adjustment:
1. With the TV menu on your video display, press the
M
/
N
/
K
/
L
Navigation Buttons A as needed
so that the current Level Adjustment setting on the
second line in the middle portion of the video display
is highlighted.
2. Press the Enter Button P and within five sec-
onds press the
M
/
N
Navigation Buttons A so
that the desired increase or decrease in the input
level is highlighted in the Options Description Line
é at the very bottom of the display screen.
3. Press the Enter Button P to enter the new set-
ting to the HS 100’s memory.
AUX Menu
In addition to the built-in DVD/CD player, tuner and “TV”
inputs, you may connect another analog audio input to
the HS 100 through the AUX Inputs 7 on the rear
panel. To listen to that source, do one of the following:
1. If the HS 100 is in the Standby mode, press the
AUX Button on the remote to turn on the unit
and go directly to the TV input.
2. If the HS 100 is already on, press the AUX Button
on the remote to switch the input, or press the
Source Button 6 on the front panel until the tuner
is the active input.
The AUX menu allows you to make configuration set-
tings for the AUX Inputs 7.
Audio: This line lets you select the surround mode that
is used when the AUX input is selected. To change the
default mode, follow these steps:
1. With the TV menu on your video display, press the
M
/
N
/
K
/
L
Navigation Buttons A as needed
so that that the current surround mode to the right of
the Audio line at the top of the menu screen is high-
lighted.
2. Press the Enter Button P, and within five sec-
onds press the
M
/
N
/
K
/
L
Navigation Buttons
A to highlight the desired surround mode.
3. Press the Enter Button P to set that mode as
the new default for the TV input.
Level Adjustment: This line lets you increase or
decrease the input level for the Aux input to compen-
sate for any variations that may be caused by the
source device. In most cases you will not need to
adjust this setting, but if the audio level when the Aux
input is selected appears lower or higher than other
sources, follow these steps to make an adjustment:
1. With the AUX menu on your video display, press
the
M
/
N
/
K
/
L
Navigation Buttons A as
needed so that the current Level Adjustment setting
on the second line in the middle portion of the video
display is highlighted.
2. Press the Enter Button P and within five sec-
onds press the
M
/
N
Navigation Buttons A so
that the desired increase or decrease in the input
level is highlighted in the Options Description Line
é at the very bottom of the display screen.
3. Press the Enter Button P to enter the new set-
ting to the HS 100’s memory.
Digital In Menu
In addition to all analog audio and video sources, the
HS 100 also gives you the opportunity to connect two
digital audio sources, for instance a digital set-top box
or satellite receiver. Connect these sources to either
the coaxial or optical digital input connectors on the
rear panel.
1. Press the On Button
0
or Digital In Button
on the remote control to turn the DVD receiver on.
Make sure that the Main Power Switch on the front
panel is in the On position, shown by the blue LED
surrounding the button. Also make sure that your
video monitor connected to the HS 100 is
switched on.
2. Press the Digital In Button
on the remote
control or Source Button
4
on the front panel
repeatedly to select one of the digital sources as the
input. The TV monitor will show the DIGITAL
IN menu, as shown below. You can also select the
DIGITAL IN menu with the Arrow Keys
9
on the remote control. Once the DIGITAL
IN tab is highlighted, press Enter Button
6
to access it.
Digital Input: This line selects which of the two digital
sources will be used when the Digital Input is selected.
You may go to this menu at any time to switch between
the two digital sources.
1. With the DIGITAL IN menu on your video
display, press the
M
/
N
/
K
/
L
Navigation
Buttons A as needed so that the current selec-
tion to the right of the Digital Input line at the top of
the menu screen is highlighted.
2. Press the Enter Button P, and within five
seconds press the
M
/
N
/
K
/
L
Navigation
Buttons A so that the desired input mode is
highlighted.
To Next Page
Loading...
