Harman Kardon PM655 Vxi - Page 6

an/kardon PM655 Vx
High Voltage
rent
HEADPHONES.
speafiers 1
off, speakers 2
Tr +2
(|
i
|
BALANCE
tone flefeat
(ma
tral
turnjiver
faa
(eal pate
bq
turnliver
te
(alleen
BASS TREBLE
WL
L
CAP. TRIM
+1000 OF
pre phaseforrect subginic higlf cut nde VOLUME +.200pf ATS
mag-in loudfless +200pt -( i)
integrand NED,
Of O OO (mi) CI... des
\ ,
i, G
e e e e e e
VCR/TAPE MONITOR RECORD OUT FUNCTION
source off tuner
1 a £ ‘ 2 copy—t to 2 ‘ 1 F source: aux ¢ 1 j co
Ty Es to 1, ry _ tuner AN. jul _ Phono cartridge
| Pre
]
|
[jt
@ POWER SWITCH (POWER)
Pressing this switch will turn on the power and the HIGH
CURRENT indicator lights up. Press the switch again to turn
the power off.
@ HIGH CURRENT INDICATOR (High Current)
When the POWER switch is pressed, this indicator lights up
in red.
© HIGH VOLTAGE INDICATOR (High Voltage)
This lights when the SPEAKER OPERATING MODE switch
on the rear panel is set to the “82” position. (Refer to the
“Connecting Speakers” section on page 3.)
@ HEADPHONE JACK (HEADPHONES)
Stereo headphones with a standard 1/4 inch plug can be
connected to this jack. When the SPEAKER selector is in the
“off” position, sound can still be obtained via the headphone
jack.
@ BASS CONTROL KNOB (BASS)
This knob controls the low frequency sound level. Turn it
clockwise to boost or counterclockwise to reduce the low
frequency sound level.
@ BASS TURNOVER SELECTOR (bass turnover)
This switch is used to select the bass turnover frequency. By
pressing this switch to set to the “200Hz” position, the low
frequency sound below 200Hz is controlled by the BASS
control knob. By releasing this switch to set to the “400Hz”
position, the low frequency sound below 400Hz is controlled
by the BASS control knob.
@ TONE DEFEAT SWITCH (tone defeat)
This switch is used to make the frequency characteristic flat
by internally bypassing the tone control circuitry. Set this
switch to the OFF position (button out) when you want to
use the tone control knobs.
@ TREBLE CONTROL KNOB (TREBLE)
This knob controls the high frequency sound level. Turn it
clockwise to boost or counterclockwise to reduce the high
frequency sound level.
20 21
18
@ TREBLE TURNOVER SELECTOR (treble turnover)
This switch is used to select the treble turnover frequency.
By pressing this switch to set to the “6kHz” position, the high
frequency sound above 6kHz is controlled by the TREBLE
control knob. By releasing this switch to set to the “2kHz”
position, the high frequency sound above 2kHz is controlled
by the TREBLE control knob.
@ BALANCE CONTROL KNOB (BALANCE)
This knob is used to balance the left and the right channels.
Usually, it is set at the center. Turn it to the left or right to
balance the sound if it seems unbalanced from the speakers
or the headphones.
@ SPEAKER SELECTOR
This selector is used to select the desired speaker system(s).
off : Select this position to listen to sound via the
headphone with no sound from the speaker
system(s).
speakers 1 : Select this position to actuate the speaker system
connected to the SPEAKER SYSTEM 1 terminal.
speakers 2 : Select this position to actuate the speaker system
connected to the SPEAKER SYSTEM 2 terminal.
1+2 : Select this position to actuate simultaneously
the two speaker systems connected to the
SPEAKER SYSTEM 1 and 2 terminals respec-
tively.
@ PRE-OUT/MAIN-IN SWITCH (pre-out main-in)
Usually this switch is kept in the “integrated” position. By
depressing this switch to the “separate” position, the pream-
plifier and power amplifier sections are separated from each
other for independent function. To use the preamplifier section
independently, connect the input jacks of the other power
amplifier to the PRE-OUT jacks on the rear panel. To use the
power amplifier section independently, connect the output
jacks of the other preamplifier to the MAIN-IN jacks on the
rear panel.