HART HGSP01 - DRAINING THE TANK; CLEANING THE TANK AND SPRAY WAND ASSEMBLY; CLEANING THE NOZZLE; REPLACING SEALS

9 – English
WARNING:
Whenservicing,useonlyidenticalreplacementparts.
Useofanyotherpartsmaycreateahazardorcause
productdamage.
WARNING:
Neverusewateroranyliquidstocleanorrinseoffthe
outside of your product and do not expose the product
torainorwetconditions.Storeindoorsinadryarea.
Corrosiveliquids,water,andchemicalscanenterthe
product’selectroniccomponentsand/orbatterycom-
partmentanddamageelectroniccomponentsand/or
the battery pack, which can result in a short circuit, in-
creasedriskoffire,andseriouspersonalinjury.Remove
any buildup of dirt and debris by wiping the product
cleanwithadryclothoccasionally.
NOTICE:
Periodicallyinspect theentireproductfordamaged,
missing, or loose parts such as screws, nuts, bolts,
caps,etc.Tightensecurelyallfastenersandcapsand
do not operate this product until all missing or damaged
partsarereplaced.Pleasecontactcustomerserviceor
anauthorizedservicecenterforassistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plasticsaresusceptibletodamagefromvarious types of
commercialsolventsandmaybedamagedbytheiruse.Use
cleanclothstoremovedirt,dust,oil,grease,etc.
WARNING:
Do not at any time let brake fluids, gasoline, penetrating
oils,etc.,comeincontactwithplasticparts.Chemicals
can damage, weaken, or destroy plastic which may
resultinseriouspersonalinjury.
CLEANING THE UNIT
See Figure 12.
WARNING:
Alwaysstoreanddisposeofchemicalsproperly.Dis-
posal of contaminated rinse water should be performed
accordingtolocalordinancesandbylaws.
DRAINING THE TANK
If there is any liquid left in the tank after spraying, the tank
shouldbedrainedbeforecleaning.
Removethebatterypack.
Removethe motor housingfrom the tankby lifting up
andreleasingthelatchesoneachendoftheunit.
Drainthecontentsofthetankthroughthefillarea.
NOTE: Drainthecontentsbackintotheoriginalcontainer.
Donotstorechemicalsinthetank.
CLEANING THE TANK AND SPRAY WAND ASSEMBLY
Fillthetankaboutone-thirdfullwithcleanwater.Asmall
amountofmildhouseholddetergentmaybeadded.
NOTE: Neveruseflammablechemicalsorabrasiveclean-
ingagentstocleanthetank.
Wipetheoutsideofthetankwithaclean,drycloth.
Reattachthemotorhousingtothetank.Makesurethe
latchesareclosed.
Reinstallthebatterypack.Sprayuntilthetankhasbeen
emptied.Makesuretodirectthespraytowardanarea
thatwillnotbedamagedbythespraysolution.
Refillandrepeattheprocedurewithcleanwater.Itmay
be necessary to rinse the tank more than once, then drain
againasdirectedabove.
Allowallpiecestocompletelydrybeforereinstallingparts
andstoringtheunit.
CLEANING THE NOZZLE
See Figure 13.
Ifthenozzlebecomesplugged,usethestepsbelowtoclear.


Removethebatterypack.


Unscrewandremovetheadjustablenozzlefromthespray
wand.


Pushasmallwirethroughthecrossholestoclearany
debris.Ifnecessary,rinsethecrossholesandnozzlewith
cleanwater.


Wipethenozzleandcrossholeswithacleandrycloth
andreinstallthenozzle.
REPLACING SEALS
See Figure 14.
Over time, seals can harden and crack, which can allow
thechemicalsprayertoleak.Refertotheimageshownfor
the location of each of the seals, then replace as needed to
addressanyleaksthatdevelop.
Additional sets of replacement seals can be ordered by
contactingcustomerservice.
NOTE: Unthreading the connections to replace the seals
could allow liquid to escape, so always clean the chemical
sprayerthoroughlyaspreviouslydescribedbeforereplac-
ingtheseals.
MAINTENANCE