5.31 inch
cut line
fold line
12 inch
front
coverpage 6page 5
page 4page 3page 2
back
1
2
3 4
1
2
3 4
pairing
The buds will start to ash red and
white, this means that they are
ready to pair.
Use the Bluetooth settings on your
device to pair with HEYDAY EARBUD
05. When the earbuds have
successfully paired they will turn
white ve seconds and then fade.
To pair the earbuds to your device
for the rst time open the case and
remove both earbuds.
To reenter pairing put both earbuds
back in the charging case with the
lid open. Hold the reset button on
the back so the case power
indicator ashes 3 times. To reset to
factory settings hold it so the
indicator ashes 6 times. After
reentering pairing or resetting start
the pairing process at step 1.
earbuds
open case
rightleft
back
earbud power
indicator
earbud power
indicator
touch sensor
microphone
touch sensor
microphone
input
USB-C
port
reset
button
case power
indicator
• TWS Earbuds
• TWS Earbud Case
• USB-C Charging Cable
• Small,Medium and Large Earbud Tips
included
indicators
Earbud Rapid Flashing Red/White - Pairing mode
Earbud Flashes White and Fades - Paired
Earbud Flashing Red - Low power
Earbud Solid Red - Charging
Earbud No Light - Charging complete
Case One Light - 25% charged
Case Two Lights - 50% charged
Case Three Lights - 75% charged
Case Four Lights - 100% charged
Ascending Tones - Power on
Descending Tones - Power o
Three Rapid Tones - Ready to pair
Single Chime - Paired
Two Rapid Dings - Low battery
Quick Beep - Next(R) / previous(L) song
touch controls
quick tip: the touch sensor is located in the center of the earbud, be sure to touch
here so inputs register
* - indicates that the left and right earbud have a dierent function
orleft earbud right earbud
hold 2 sec.
- next song*
- reject call
- prev. song*
- reject call
1 tap
- play/pause
- answer/end call
- play/pause
- answer/end call
2 taps
- voice assist- voice assist
1 2
3
1 2
3
earbud tips
To change the size of the earbud
tip, squeeze it and pull it away from
the earbud.
Select the size that is the most
comfortable for you and push it
onto the earbud. The earbud tip has
an interior sleeve that slides onto
the earbud. Repeat steps 2 and 3
for the second earbud.
The earbuds come with small,
medium and large earbud tips and
can be changed at any time.
Place both earbuds back into the case
Charging is complete when lights turn o
Full charge requires approximately 1 hour
charging earbuds
• After pairing to your device remove only the right earbud from the case to enter single
earbud use
single earbud use
• Plug USB-C end of charger into the back of the case
• Plug USB end into a power supply of at least DC 5V 1A warning: please use UL
compliant power supply
• Full charge requires approximately 2 hours and will provide 24 hours of earbud use
• Charging is complete when all 4 LEDs are solid white
charging case
• The earbuds are resistant to sweat which means they’re perfect for workouts note: the
charging case does not have the same rating and should not be used in the same conditions
IPX5 water resistance
hey! welcome to your Heyday™ true
wireless earbuds. let’s get you set up.
welcome!
coverpage 6
how to fold
DO NOT PRINT
page 5
• Do not use near any water source
• Do not modify or repair this device
• Do not use chemical detergents to clean your device, use a soft dry cloth
WARNING: The battery (battery or batteries or battery pack) shall not be exposed to
excessive heat such as sunshine, re or the like
safety
Can’t get it to pair? Have a question or comment?
call us at: 877-698-4883 or: 877-MyTgtTech
online at: TargetTechSupport.com
need some help?
• If the earbuds are not working correctly place them into the case with the lid open
and reset them
• If the earbuds won’t turn on, recharge the battery and try again
• If the earbuds won’t charge, make sure the power supply works, is 5V>1A, not
damaged and that the case is charged
• If the earbuds still won’t charge, make sure the charge pins are clear of debris as this
may cause a connection issue; if they are use a soft dry cloth to clean them
• If the earbuds make no sound or do not show as an available device, make sure they
are not paired, if so unpair the device and repair to the desired device
troubleshooting
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC ID: 2AO23-TW15C Model: TW15C Input: 5V Max 1A Earbud Battery Capacity: 3.6V/60mAh/0.216Wh Case Battery Capacity: 3.7V/ 500mAh/ 1.850Wh Made in China
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2)
this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Target Corp. Mpls. MN, 55403 Phone: 1-612-304-6073
To Previous Page
Loading...
