Need help?Do you have a question about the Hikari HX688T and is the answer not in the manual?
General| Brand | Hikari |
|---|---|
| Model | HX688T |
| Category | Industrial Equipment |
| Language | English |
Essential safety rules to follow when operating the sewing machine.
Procedures for power off in case of threading, repair, or unattended operation.
Detailed warnings about electrical shock, entanglement, and sudden starts.
Describes the purpose and scope of the instruction manual.
Explains danger, warning, and caution symbols used in the manual.
Factors in the operating environment that affect machine performance and safety.
Precautions for maintenance, inspection, and repair tasks.
Checks before operation, operator training, and unpacking instructions.
Procedures for handling packaging and machine waste.
Guidelines for safely moving and transporting the sewing machine.
Requirements for machine table setup and electrical wiring.
Proper grounding procedures and precautions for using sewing machine oil.
Safety checks before starting and during machine operation.
Safety guidelines to follow during sewing machine operation.
Safety procedures for machine maintenance, inspection, and repair.
Diagram showing the placement of warning labels and safety devices.
Details on eye guards, finger guards, presser feet, and covers.
Detailed dimensions and specifications for the sewing machine table board.
Guidelines for selecting and supplying the correct machine oil.
Procedures for manual oiling and checking oil circulation.
Supplying oil to HR unit and replacing machine oil.
Procedures for checking, cleaning, or replacing the filter.
Safety precautions for cleaning the sewing machine.
Step-by-step guide for threading the machine, including stitch type diagrams.
Instructions for safely replacing the sewing machine needle.
How to adjust thread tension for optimal sewing results.
Procedures for operating and adjusting presser foot pressure.
Adjusting the differential feed ratio for fabric handling.
Adjusting stitch length and safety notes for blade work.
Steps for safely replacing the upper knife blade.
Procedures for replacing the lower knife and adjusting chain width.
Instructions on how to properly sharpen the machine knives.
Positioning and adjusting the needle thread lever.
Setting and adjusting the needle thread guides.
Specific installation positions for thread guides in five-thread configurations.
Adjusting thread guides for three and four-thread sewing machines.
Adjusting chain looper thread levers, guides, and take-up amount.
Adjusting standard positions of looper thread levers and guides.
Diagrams and specifications for looper thread lever and guide installation.
Reference table for adjustment values for five and six-thread series.
Reference table for adjustment values for three and four-thread series.
Table showing standard needle types for five and six-thread series.
Table showing standard needle types for three and four-thread series.
Specifications for five and six-thread series HX models.
Specifications for three and four-thread series HX models.
Selecting and operating puller functions via the control panel.
Adjusting the lifting height, pressure, and gap of the puller wheel.
Adjusting the feed speed of the puller wheel.
Configuration reference for puller wheels on specific machine models.
Selecting side suction functions, loose line assembly, and cutter details.
Procedures for maintaining the side suction knife components.
General safety precautions for operating the sewing machine.
Safety instructions for maintenance and operation tasks.
Describes the purpose and scope of the instruction manual.
Explains danger, warning, and caution symbols used in the manual.
Factors in the operating environment that affect machine performance and safety.
Precautions for maintenance, inspection, and repair tasks.
Checks for securing components like the ferrule and presser foot.
Operator training, unpacking, and waste disposal guidelines.
Guidelines for safely moving and transporting the sewing machine.
Requirements for machine table setup and electrical wiring.
Proper cable management, fastening, and grounding procedures.
Safe handling of machine oil and pre-start checks.
Importance of manual reading, understanding warnings, and speed settings.
Precautions during machine operation and safety for maintenance tasks.
Diagram showing the placement of warning labels and safety devices.
Details on eye guards, finger guards, presser feet, and covers.
Diagram illustrating the sewing machine table setup.
Important note regarding the use of company-supplied oil.
Procedures for oil supply, manual refueling, and circulation checks.
Supplying HR unit oil, replacing machine oil, and draining procedures.
Procedures for checking, cleaning, or replacing the filter.
Safety precautions for cleaning the sewing machine.
Step-by-step guide for threading the machine, including stitch type diagrams.
Procedures for replacing needles and adjusting thread tension.
Procedures for operating and adjusting the presser foot and switch.
Adjusting the differential feed ratio for fabric handling.
Adjusting stitch length and safety notes for blade work.
Steps for safely replacing the upper knife blade.
Procedures for replacing the lower knife and adjusting chain width.
Instructions for knife sharpening and needle wire setup.
Diagrams illustrating thread guide components and adjustments.
Adjusting wire parts for proper looping action.
Specific installation positions for thread guides in five-thread configurations.
Adjusting thread guides for three and four-thread sewing machines.
Standard mounting positions for needle thread guides.
Procedure for installing and adjusting the line CAM.
Adjusting looper thread guides and thread take-up amount.
Standard installation positions for curved needles and threads.
Reference table for adjustment values for five and six-thread series.
Reference table for adjustment values for three and four-thread series.
Table showing standard needle types for five and six-thread series.
Table showing standard needle types for three and four-thread series.
Specifications for HX series models based on thread count.
Selecting and operating puller functions via the control panel.
Details on puller functions, height, pressure, speed, and adjustments.
Lab-wheel configuration data for specific HX series models.
Selecting and operating puller equipment and side suction functions.
Procedures for maintaining the side suction knife components.
To Next Page
