HIMA HIMax X-DI 64 51 - Coding of X-CB 006 5 X Connector Boards; Figure 5: Coding Example; Table 11: Position of Coding Wedges

50 pages

To Next Page

To Previous Page

X-DI 64 51 3 Product Description

HI 801 177 E 4.00 Page 19 of 50

Male Connector Recess

Prepared Male Connector Recess

Coding Wedge

Guideway for Coding Wedge

Figure 5: Coding Example

3.6.2 Coding of X-CB 006 5X Connector Boards

a7 a13 a20 a26 e7 e13 e20 e26

X X X

Table 11: Position of Coding Wedges

Main Page

Table of Contents3
Introduction5
Structure and Use of this Manual5
Target Audience5
Table 1: Additional Relevant Manuals5
Formatting Conventions6
Safety Notes6
Operating Tips7
Safety8
Intended Use8
Environmental Requirements8
ESD Protective Measures8
Table 2: Environmental Requirements8
Residual Risk9
Safety Precautions9
Emergency Information9
Product Description10
Safety Function10
Reaction in the Event of a Fault10
Scope of Delivery10
Type Label11
Figure 1: Sample Type Label11
Structure12
Block Diagram12
Figure 2: Block Diagram12
Indicators13
Figure 3: Indicators13
Module Status Indicators14
Table 3: Blinking Frequencies of Leds14
Table 4: Module Status Indicators14
System Bus Indicators15
I/O Indicators15
Table 5: System Bus Indicators15
Table 6: I/O Indicators Leds15
Product Data16
Figure 4: Views16
Table 7: Product Data16
Table 8: Specifications for Digital Inputs17
Table 9: Product Data for Supply17
Connector Boards18
Mechanical Coding of Connector Boards18
Table 10: Available Connector Boards18
Coding of X-CB 006 5X Connector Boards19
Figure 5: Coding Example19
Table 11: Position of Coding Wedges19
Connector Boards with Screw Terminals20
Figure 6: Connector Boards with Screw Terminals20
Terminal Assignment for Connector Boards with Screw Terminals21
Table 12: Terminal Assignment for Connector Boards with Screw Terminals22
Table 13: Cable Plug Properties22
Connector Boards with Cable Plug23
Figure 7: Connector Boards with Cable Plug23
Pin Assignment for Connector Boards with Cable Plug24
Table 14: Pin Assignment for the System Cable Plug24
System Cable25
Figure 8: System Cable X-CA 003 01 N25
Table 15: Cable Data25
Table 16: Available System Cables25
Cable Plug Coding26
Start-Up27
Mounting27
Wiring Inputs Not in Use27
Mounting and Removing the Module28
Mounting a Connector Board28
Figure 9: Inserting the Connector Board28
Figure 10: Securing the Connector Board with Captive Screws29
Mounting and Removing the Module30
Figure 11: Mounting and Removing a Module31
Configuring the Module in Silworx32
Tab: Module33
Table 17: Module Tab in the Hardware Editor33
Tab: I/O Submodule DI64_5134
Table 18: Tab: I/O Submodule DI64_51 in the Hardware Editor34
Tab: I/O Submodule DI64_51: Channels35
Table 19: Tab: I/O Submodule D64_51: Channels in the Hardware Editor35
Submodule Status [DWORD]36
Table 20: Submodule Status [DWORD]36
Diagnostic Status [DWORD]37
Table 21: Diagnostic Information [DWORD]37
Connection Variants38
Input Wiring38
Figure 12: Wiring with Contact Maker or Two-Wire Proximity Switch38
Figure 13: Wiring of a Digital Signal Source with Electrically Isolated Supply38
Figure 14: Wiring of a Digital Signal Source with Non-Electrically Isolated Supply39
Figure 15: Redundant Wiring with Contact Maker or Two-Wire Proximity Switch39
Wiring Transmitters Via Field Termination Assembly40
Figure 16: Redundant Wiring of a Digital Signal Source with Electrically Isolated Supply40
Figure 17: Connection Via Field Termination Assembly40
Operation41
Handling41
Diagnosis41
Maintenance42
Maintenance Measures42
Loading the Operating System42
Proof Test42
Decommissioning43
Transport44
Disposal45
Appendix46
Glossary46
Index of Figures47
Index of Tables48
Index49

HIMA HIMax X-DI 64 51 - Coding of X-CB 006 5 X Connector Boards; Figure 5: Coding Example; Table 11: Position of Coding Wedges

Table of Contents

Related product manuals