Hitachi EH-150 - 5.4.5 ASR Parameters Setting Error Code

Chapter 5 Configuration of Communication parameters
5.4.5 ASR parameters setting error code
The list of error code of ASR parameters setting is shown in Table 5.22.
Table 5.22 ASR parameters setting error code
Error
code
Comment Cause
2101 General information (No.n): Port No. is incorrect. Illegal value or character is set for ASR connection n
(*1)
port
number
2102 General information (No.n): Other station IP address
is incorrect.
At ASR connection n
(*1)
- Illegal value or character is set for ASR other station IP
address.
- The out of value of “0.0.0.0” to “255.255.255.255” is set
for ASR other station IP address.
2103 General information (No.n): Other station Port No. is
incorrect.
Illegal value or character is set for ASR other station port
number at ASR connection n
(*1)
.
2104 General information (No.n): Cyclic time is incorrect. Illegal value or character is set for cyclic transmission time
at ASR connection n
(*1)
.
2105 General information: Timeout is incorrect. Illegal value or character is set for ASR connection timeout.
2106 General information (No.n): Port No. is in conflict
with ASR connection m.
The port number of ASR connection n
(*1)
and the port
number of ASR connection m
(*1)
is in coincidence(conflict).
2107 General information (No.n): Port No. is in conflict
with Task code connection p.
The port number of ASR connection n
(*1)
and the port
number of Task code connection p
(*2)
is in
coincidence(conflict).
2108 General information (No.n): Port No. is in conflict
with the Diagnostic port.
The port number of ASR connection n
(*1)
and the port
number of diagnostic is in coincidence(conflict).
2109 General information (No.n): Other station must be
specified.
ASR connection n
(*1)
is active station, but "Optional" is
selected for other station.
2202 Receive Information (No.n): Top is incorrect. At ASR connection n
(*1)
, illegal value or character is set for
Top I/O address of receive area.
2203 Receive Information (No.n): Size is incorrect. At ASR connection n
(*1)
, illegal value or character is set for
I/O Size of receive area.
2204 Receive Information (No.n): Top + Size exceeds the
limit.
At ASR connection n
(*1)
, data size of receive area is over the
supported I/O area of CPU module.
2302 Send Information (No.n): Top is incorrect. At ASR connection n
(*1)
, illegal value or character is set for
Top I/O address of send area.
2303 Send Information (No.n): Size is incorrect. At ASR connection n
(*1)
, illegal value or character is set for
I/O Size of send area.
2304 Send Information (No.n): Top + Size exceeds the
limit.
At ASR connection n
(*1)
, data size of send area is over the
supported I/O area of CPU module.
2305 Send Information (No.n): Total size is too big. At ASR connection n
(*1)
, total send data size is over 727
words.
2306 Send Information: Item No. conflict. Item number of Send areas are duplicated.
2601 General information (No.n): Open Retry Times is
incorrect.
At ASR connection n
(*1)
, illegal value or character is set for
Open Retry Times.
2602 General information (No.n): Open Retry Interval is
incorrect.
At ASR connection n
(*1)
, illegal value or character is set for
Open Retry Interval(Retry Times != 0, Interval = 0).
*1: n or m should be in 1 to 6.
*2: p should be in 1 to 4.
5-29