– 174 –
10. Ion mist unit
Ion mist unit
Ion mist discharge
electrode
Electrode box for
dust collection
The equipment has high voltage (about
-6 kV), which causes danger. Therefore
do not under any circumstances touch
anything such as in measuring the
output voltage while the product is
energized.
Microcomputer
IC601
Check
Check
Check
Equipment cover
1
Vin
2
3
4
12
ERR
GND
REM(ON/OFF)
2
3
4
1
R703
R702
C701
19
18
5
CN13
CN14
36
94
R701
5V
0V
R708
ICP1
R707
C616
R706
C619
R705
0V0V
0V
0V
Q702
12V
12V
0V
L921
D921
R931
R932
R933
0V
0V
12V
5V
R934
R935
R936
C931
C932
D931
1
+
-
2
3
8
4
C933
C920
+
12
12
IC931
R921
C921
R924
R923
Q921
Q922
R922
Detection switch for front
panel open/closed states
High-voltage generator
Peltier
High-voltage
abnormality
(Lo abnormal,
Hi normal)
High voltage output
Front panel
Peltier power
supply
Peltier Id
・The ion mist unit causes the discharge electrode for ion mist to absorb water generated as a result of condensation
stemming from a cooled Peltier device. It then uses a high-voltage generator to apply high voltage, thereby discharging ion
mist.
・ The ion mist unit applies a voltage of about -6 kV.
・ To prevent electric shocks, a "detection switch for front panel open/closed states" is installed. Opening the front panel will
forcibly stop the supply of power supply voltage 12 V of the ion mist unit.
・ The ion mist unit starts to run as controlled by the microcomputer (IC601) when set to "ion mist operation" by remote
control.
・ "Ion mist operation" can be configured when the product is running in any of the following modes: "cooling," "heating,"
"dehumidification," or "comfortable cooling." The product can also be run in "ion mist operation" alone.
・ When configured to "air purification," the product will not discharge ion mist. For that reason, the electrical dust collector
alone will be activated.
Fig. 10-1
When extreme dirt on an electrode increases the output current from the high-voltage generator, resulting in a decline in
output voltage, the ion mist unit may stop.
In that case, the product will give a failure display, causing the "mist and air purification lamp" to remain on for 4 seconds
and off for 1 second. If the above factors are absent and if the "mist and air purification lamp" remains on for 4 seconds
and off for 1 second as a failure display, it should be either the CN14 connector being loose or the high-voltage generator
having a failure.
※Even if the above failure display is on, the ion mist unit alone will stop. The air-conditioner proper will remain trouble-free
for operation.
※The ion mist unit will perform judgment by prolonged sampling in order to prevent erroneous detection. There is a mode
where, to perform failure judgment in a short time at the time of servicing, and if the first signal received from the remote
control unit after power-on is "air purification," the product will give a failure display about 10 seconds later.
When the Peltier device fails, the ion mist unit will stop.
In that case, the failure display will occur and the "mist and air purification lamp" will remain on for 4 seconds and off for 3
seconds. If the above factors are absent and if the "air purification lamp" remains on for 4 seconds and off for 3 seconds
(thereby giving a failure display), it should be either the CN19 connector being loose or the Peltier power circuit having a
failure.
※Even if the above failure display is on, the ion mist unit alone will stop. The air-conditioner proper will remain trouble-free
for operation.
※The ion mist unit will perform judgment by prolonged sampling in order to prevent erroneous detection. There is a mode
where, to perform failure judgment in a short time at the time of servicing, and if the first signal received from the remote
control unit after power-on is "air purification in isolation," the product will give a failure display about 10 seconds later.
When the front panel is open, or when the CN13 connector is loose, the "clean lamp" will remain on for 1 second and
remain dimmed for 1 second. The ion mist unit will then stop.
Correctly mounting the front panel will cancel the blinking, with the ion mist unit becoming operable.
To Next Page
Loading...
