Hitachi Relion SAM600

To Next Page

To Previous Page

Document ID: 1MRK511447-UEN

Issued: June 2023

Revision: E

Product version: 2.2

Main Page

Table of Contents7
Introduction11
This Manual11
Intended Audience11
Product Documentation11
Product Documentation Set11
Document Revision History12
Related Documents13
Document Symbols and Conventions13
Symbols13
Document Conventions14
IEC 61850 Edition 1, Edition 2, and Edition 2.1 Mapping14
Safety Information17
Symbols on the Product17
Warnings17
Caution Signs18
Available Functions19
Control and Monitoring Functions19
Communication20
Basic IED Functions21
User Interface23
Introduction23
PCM600 Tool23
Connectivity Packages23
SAM600-IO LHMI Service Kit23
Display24
Keypad24
LED Indication26
Front Communication27
Connecting the LHMI Service Kit to SAM600-IO28
Removing the LHMI Service Kit from SAM600-IO28
Starting up29
Factory and Site Acceptance Testing29
Commissioning Checklist29
Checking the Power Supply29
Energizing the IED30
Checking the IED Operation30
IED Start-Up Sequence30
Setting up Communication between PCM600 and the IED31
When IED Has Blank Front Panel31
When IED Has Front Port with RJ-4531
Writing an Application Configuration to the IED36
Using the RTXP Test Switch36
Checking the Binary Input/Output Circuits36
Binary Input Circuits36
Checking Optical Connections36
Configuring the IED and Changing Settings39
Overview39
Supervision of Input/Output Modules39
Establishing Connection and Verifying the IEC 61850 Communication41
Overview41
Setting the Station Communication41
Verifying the Communication41
Testing IED Operation43
Preparing for Test43
Requirements43
Preparing the IED to Verify Settings44
Activating the Test Mode44
Preparing the Connection to the Test Equipment45
Connecting the Test Equipment to the IED45
Releasing the Function to be Tested46
Forcing of Binary Input/Output Signals for Testing47
Forcing Concept47
How to Enable Forcing47
Enable Forcing Using TESTMODE Function Block47
How to Change Binary Input/Output Signals Using Forcing47
Forcing by Using PCM60047
How to Undo Forcing Changes and Return the IED to Normal Operation49
Undo Forcing by Using TESTMODE Component49
Undo Forcing by Using PCM60049
Testing Functionality by Secondary Injection51
Testing Disturbance Report51
Introduction51
Disturbance Report Settings51
Disturbance Recorder (DR)51
Event Recorder (ER) and Event List (EL)52
Identifying the Function to Test in the Technical Reference Manual52
Control52
Apparatus Control APC52
Logic52
Tripping Logic, Common 3-Phase Output SMPPTRC52
Three-Phase Operating Mode52
1Ph/3Ph Operating Mode53
1Ph/2Ph/3Ph Operating Mode53
Circuit Breaker Lockout54
Completing the Test55
Monitoring55
Gas Medium Supervision SSIMG55
Testing the Gas Medium Supervision for Pressure Alarm55
Testing the Gas Medium Supervision for Temperature Alarm55
Liquid Medium Supervision SSIML55
Testing the Liquid Medium Supervision for Level Alarm and Level Lockout Conditions55
Testing the Gas Medium Supervision for Temperature Alarm and Temperature Lockout Conditions56
Completing the Test56
Breaker Monitoring SSCBR56
Verifying the Settings56
Completing the Test58
Limit Counter L4UFCNT58
Basic IED Functions58
Parameter Setting Group Handling SETGRPS58
Verifying the Settings58
Completing the Test59
Exit Test Mode59
Commissioning and Maintenance of the Fault Clearing System61
Commissioning Tests61
Periodic Maintenance Tests61
Visual Inspection61
Maintenance Tests61
Preparation62
Recording62
Secondary Injection62
Alarm Test62
Self Supervision Check62
Trip Circuit Check63
Restoring63
Troubleshooting65
Checking the Self Supervision Signals65
Checking the Self Supervision Function65
Determine the Cause of an Internal Failure65
Self Supervision Data65
General IED Status65
Fault Tracing66
Internal Fault Indications66
Using LHMI Service Kit-Connected PC67
Diagnosing the IED Status Via the LHMI Hint Menu68
Hardware Re-Configuration69
Repair Instruction70
Repair Support70
Maintenance70
Glossary71

Related product manuals

Hitachi HC Series

4 pages

Hitachi Relion SAM600 - Page 3

Table of Contents

Related product manuals