HMDX Jam Zzz - Operating the Jam Zzz Bedside Sound System; Power Source and Clock Setting; Alarm Setup and Operation; Audio Playback Modes

4 5
Turning Off the Alarm/Snooze Operation
TheJAMZzzisequippedwithgradualwake,whichmeansthatthealarmbeginssoftand
slowly gets louder. This will ensure a non-jarring wakeup.
1. PresstheSNOOZEbarlocatedonthetopoftheunitandthealarmwillsoundagainin
nine minutes.
Please note: You may only press the Snooze button during the Alarm mode for one
hour(6times).Afterthesixthtime,thealarmwillturnoffandwillnotsoundagainuntil
the next set time.
2. Toturnoffthealarm,pressthe(ALARM1orALARM2)buttononthetopoftheunit.
Listening to your device wirelessly over Bluetooth
®
To connect to Bluetooth
1. PressthePOWERbuttonlocatedontopoftheunit.
2. PresstheSourcebuttonontopofunituntil“BT”iconimageappearsontheLCD
screen.
3. Followtheinstructionsofyourdevicetopairtheunit.
4. Pair your device with the unit by selecting JAM Zzz from your Bluetooth
®
listings
onyourdeviceorselectingYES.JamZzzwillsoundahinttoneoncepairinghas
occurred.
5. Press play on the connected device.
NOTE:Youmayneedtoadjustthevolumeonyouraudiodevicetoachieveproper
volume.
NOTE:Whenpairingwithacomputer,pleaseconsultyourcomputermanufacturerfor
Bluetooth
®
pairing instructions and/or the latest Bluetooth
®
Drivers.
Listening to a non-Bluetooth
®
audio device
1. Pluga3.5mmaudiocable(included),intotheAuxaudiolineinputlocatedontheback
of the unit.
2. Plug the other end of the audio cable into the line out or headphone jack of your audio
device.
3. PressthePOWERbuttonlocatedontopoftheJAMZzz.
4. PresstheSOURCEbuttonontheunituntiltheAuxiconappearsonthedisplay.
5. Press play on the connected device.
NOTE:Youmayneedtoadjustthevolumeonyouraudiodevicetoachieveproper
volume.
NOTE:Trackforward/reverseandplay/pausecontrolsonJamZzzwillnotworkwhen
usingLine-InAudioJack.
Power Source
ThisunitissuppliedwithanACadapter;takethefollowingstepstoconnecttheadaptor.
1. UnwindthepowercordoftheACadaptortoitsfulllength.
2. ConnecttheACadaptertotheDCInput(Fig.2).
3. PlugtheACadapterintoanoutlet(100v–240VAC50/60Hz).Connectingthissystem
toanyotherpowersourcemaycausedamagetothesystem.Forsufficientventilation,
keep other objects at least 4 inches away from the unit.
4. Topowertheunitoffcompletely,unplugtheACadapterfromthewalloutlet.
FUNCTIONALITY
Setting Clock Time – Pre-set Clock
Thisunitisequippedwithapre-setclock,meaningtheclockwillautomaticallysetitself
when first plugged in.
Pleasenote:theclockwillautomaticallydefaulttoEasternStandardTimeandwillneedto
be adjusted for other time zones by manually setting the clock.
Setting Clock Time – Manually Setting the Clock
1. Set time when unit is plugged in, but ensure the power button has not been activated
and is off.
2. PressTIMESETbuttononthebackoftheunittobegintheTimeSettingmode.Youwill
be prompted to select 24 hour or 12 hour display, use the volume buttons on the top of
theunittoselectthe24/12hourmode,pressTIMESETbuttonagaintoselectthehour
usingthevolumebuttonsonthetoptoadvancethehour(aPMindicatorwilldisplay
whenhourisadvancedaccordingly),pressTIMESETbuttonagaintoselecttheminute
using the volume buttons on the top to advance.
Setting and Using the Alarms – Setting Alarm 1 or Alarm 2
1. Pressandholdthedesiredalarmbutton(ALARM1orALARM2)locatedonthetopof
theUnit.Thehourwillbeginflashing.
2. UsetheFORWARDandREVERSEbuttons(orthevolumeup/downbuttons)ontopof
the unit to adjust the hour, paying attention to the AM and PM indicators.
3. Pressthealarmbuttonagainandtheminutewillbeginflashing.UsetheFORWARDand
REVERSEbuttonsagaintoadjusttheminute.
4. Press the alarm button again to select the source. The JAM Zzz alarm can be set to
BeeporFMusingtheFORWARDandREVERSEbuttons.Thealarmcannotbesetto
the Bluetooth
®
source.
5. Press alarm button again to adjust the maximum volume level of the gradual wake
feature(alarmbeginssoftandslowlygetsloader)byusingtheFORWARDand
REVERSEbuttonstoadjustthesoundlevelupordown.