Honda 2005 CRF250X - Tools

TORQUE VALUES
Engine oil drain bolt ('04 ~ '06)
Engine oil drain bolt (After '06)
Transmission oil drain bolt ('04 - '06)
Transmission oil drain bolt (After '06)
Crankshaft hole cap
Spark plug
Brake lever adjuster lock nut
Rear axle nut
Drive chain roller bolt/nut
Drive sprocket bolt
Driven sprocket nut
Front maste r cylinder reservoir cover screw
Rear master cylinder reservoir cover bolt
Exhaust pipe joint nut
Muffler jo int band bolt
Spark arrester mounting bolt (,04 - '06)
Spark arrester mounting bolt (After '06)
Diffuser mounting lorx screw
Spoke
Rim lock
Plug bolt
Side stand mounting bolt
Side stand pivot bolt
Side stand pivot nut
( uppe r)
(lower)
Rear master cylinder push rod lock nut
Drive chain adjusting bolt lock nut
Throttle cable upper adjuster lock nut (After '06)
Throttle cable lowe r adjuster lock nut (After '06)
TOOLS
22 N·m (2.2 kgf·m , 16 Ibf·ft)
16 N'm (1.6 kgf.m, 12 Ibf.ft)
22 N'm (2.2 kgf.m, 16 Ibf·ft)
16 N'm (1.6 kgf·m. 12 Ibf·ft)
15 N'm ( 1.5 kgf·m. 11 rbf·ft)
16 N'm (1.6 kgf.m, 12 IbUt)
5.9 N'm (0.6 kgf·m, 4.3 Ibfft)
127 N'm (13.0 kgfm , 94Ibf·ft)
12 N'm (1.2 kgf.m, 9Ibf.ft)
31 N·m (3.2 kgf'm, 23 I bUt)
32 N·m (3.3 kgf.m, 24 Ibf.f t)
1.5 N·m (0.15 kgfm, l.llbfft)
1.5 N·m (0.15 kgf.m, l.llbf·ft)
21 N·m (2.1 kgf·m, 15 Ibf·ft)
21 N·m (2.1 kg f ·m, 151bHt)
12 N'm (1.2 kgf·m. 9Ibf·ft)
6.9 N'm (0.7 kgf·m. 5.1 tbf·ft)
11 N·m (1.1 kgf·m, 8 Ibf·h)
3.7 N'm (0.38 kgf·m, 2.7 Ibf.ft)
12 N'm (1.2 kgf·m, 9 Ibf·ft)
1.3 N'm (0.13 kgf ·m,O. 9 tbf·ft)
54 N'm (5.5 kgf·m, 40 Ibf.ft)
39 N'm (4.0 kgf·m, 29 Ibf.ft )
See
page 3-31
39 N'm (4.0 kgf·m, 29 Ibf.ft)
5.9 N'm (0.6 kgf.m, 4.3 IbUt)
27 N'm (2.8 kgf·m, 20 Ibf.ft)
3.9 N'm (0.4 kgf·m, 2.9 Ibf·ft)
3.9 N'm (0.4 kgf·m, 2.9 Ibf·ft)
Drive chain tool set
07HMH-MR10103 or
Spoke wrench, 6.1 mm
07JMA-MR60100 or
lID @ ~ '@'<a:::"",{ ,J,;--.../
MAINTENANCE
Apply oil to the threads and
seating surlace
Apply oil to the threads and
seating surlace
Apply transmission oit to the
threads and seating surlace
Apply transmission oil to the
threads and seating surlace
Apply grease to the threads
U -nut
U-nut
U-nut
See page 3-30
U-nut
Spoke wrench, 6.6 mm
070MA-KZ30100 or
07HMH-MR10l0C (U.S.A. only) 07701-0020300 or
equivalent commercially available
in U.S.A.
equivalent commerc ially available
in U.S.A
L
3-3