Honeywell AreaRAE Plus - Calibration and Testing; Bump Testing and Calibration Importance

Honeywell AreaRAE Plus

124 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

AreaRAE Plus & AreaRAE Pro User’s Guide

89

4. Tilt up the cover of the battery compartment and remove it.

5. The five locations for batteries have hook-and-loop fabric strips across them. Unfasten them.

Table of Contents

Default Chapter3
- Table of Contents3
- Proper Product Disposal at End of Life11
1 Features Comparison12
2 Standard Contents13
3 General Information14
- Key Features15
4 Connections16
5 User Interface17
- Display Overview17
  - Status Indicator Icons17
  - Status Indicator Icons for Instruments Equipped with ISM Radio or Wifi19
- Keys and Interface20
  - Reverse Direction20
- Screen Display for Various Numbers of Active Sensors21
- Glance Mode21
- Menus22
  - Operation Mode Navigation22
6 Wireless Operation23
7 Wireless Control and Submenus24
- ISM Settings25
8 Wifi Settings26
- Setting Wifi Communication Parameters in Prorae Studio II26
9 Relays for Controlling External Equipment28
10 Battery30
- Charging30
- Battery States31
- External Battery Charger31
11 Turning the Arearae Plus/Pro on and off33
- Turning the Arearae Plus/Pro on33
  - Pausing to View Screens During Startup33
- Turning the Arearae Plus/Pro off33
- Testing Alarm Indicators34
- Pump Status34
- Calibration Status34
- Bump Status35
12 Programming36
- Enter Programming in Basic Mode36
- Enter Programming in Advanced Mode37
- Menus and Submenus38
13 User Modes63
- Basic User Mode63
- Advanced User Mode63
14 Policy Enforcement63
- Setting Policy Enforcement63
- Deactivating Policy Enforcement65
15 Calibration and Testing67
- Manual Alarms Test67
- Bump Testing and Calibration67
- Span Calibration70
- Three-Point Calibration for Enhanced Linearity with Extended-Range and Ppb PID Sensors70
16 Datalog Transfer, Monitor Configuration, and Firmware Upgrades Via Computer75
- Downloading Datalogs and Performing PC-Based Instrument Configuration and Firmware Upgrades75
17 Maintenance76
- Removing/Installing the Rubber Boot76
- Replacing the External Filter76
- Removing/Cleaning/Replacing Sensor Modules77
- Cleaning or Replacing the PID78
  - Cleaning or Replacing the 4R+ PID79
  - Cleaning or Replacing the 7R+ PID81
- Replacing the Sensor Compartment Cover86
- Battery Removal/Replacement86
- Alkaline Battery Pack88
- Raemet Meteorological Sensor (Optional)92
- Antenna Installation93
- Replacing the Pump94
18 Alarms Overview96
- Alarm Signals96
- Changing the Alarm Mode96
19 Diagnostic Mode97
- Enter Diagnostic Mode97
- Adjusting Alarm Leds & Buzzer97
- Adjusting LCD Contrast97
- Pump Stall Threshold Adjustment97
- Alarm Signal Summary103
  - Hygiene Mode103
  - General Alarms104
20 Troubleshooting105
21 Specifications106
22 Technical Support122
23 RAE Systems by Honeywell Contacts123

Other manuals for Honeywell AreaRAE Plus

User Manual145 pages

Related product manuals

Preview: Honeywell AreaRAE Pro

Honeywell AreaRAE Pro

Preview: Honeywell C7061 A

Honeywell C7061 A

Preview: Honeywell Activ8 PIR

Honeywell Activ8 PIR

Preview: Honeywell Viewguard DUAL AM FAI

Honeywell Viewguard DUAL AM FAI

Honeywell FIRE-LITE ALARMS H365

Preview: Fire-Lite Alarms D365PL

Fire-Lite Alarms D365PL

FIRE-LITE ALARMS SD365CO

Preview: Viewguard DUAL AM BUS-2/BUS-1

Viewguard DUAL AM BUS-2/BUS-1

Preview: Honeywell 5800CO

Honeywell 5800CO

Preview: Honeywell 5800PIR

Honeywell 5800PIR

Preview: Honeywell FlexGuard FG-1625

Honeywell FlexGuard FG-1625

Preview: Miller TurboLite Series

Miller TurboLite Series