Honeywell BC-200 - Page 5

BC-200 Manual – P/N DOC-01-013 5
8.1.1 Writing Scripts.......................................................................................................................................... 89
8.1.2 Using zone numbers in scripts:.................................................................................................................. 89
8.1.3 Making an output latch.............................................................................................................................. 89
8.1.4 ANY Operator........................................................................................................................................... 90
8.1.5 TIM Operator............................................................................................................................................ 90
8.1.6 ‘S’ Pre-Operator....................................................................................................................................... 91
8.1.7 Scripting Examples.................................................................................................................................... 91
8.2 NETWORK POINTS (WHERE APPLICABLE) ............................................................................................................ 92
8.2.1 Special Net Points..................................................................................................................................... 93
9 APPENDIX............................................................................................................................................................. 94
9.1 ZONE OPTION EXPLANATIONS ........................................................................................................................... 94
9.1.1 AVF functional description........................................................................................................................ 94
9.1.2 Timed AZF Functional Description............................................................................................................ 94
9.2 PASSWORD ACCESS LEVELS............................................................................................................................... 95
9.3 LCD80 OPERATION........................................................................................................................................... 96
9.3.1 LCD80 – Terminal Mode........................................................................................................................... 96
9.3.2 Annunciator Mode..................................................................................................................................... 98
9.4 RECOMMENDED CABLING REQUIREMENTS ....................................................................................................... 101
9.4.1 RS-485 Ring Communication Cabling...................................................................................................... 101
9.4.2 Addressable Loop Cabling....................................................................................................................... 102
9.4.3 Network cabling...................................................................................................................................... 103
9.5 INTELLIGENT SENSING FEATURES .................................................................................................................... 104
9.5.1 Detector Initialisation ............................................................................................................................. 104
9.5.2 Self-Optimizing Pre-Alarm ...................................................................................................................... 104
9.5.3 Detector Sensitivity ................................................................................................................................. 105
9.5.4 Drift Compensation................................................................................................................................. 107
9.5.5 Fault Codes............................................................................................................................................. 108
9.6 PANEL CONNECTION DIAGRAMS:..................................................................................................................... 110
9.6.1 Main Termination Board (FIM)............................................................................................................... 110
9.6.2 CPU........................................................................................................................................................ 114
9.6.3 Loop Interface Module (LIM) .................................................................................................................. 115
9.6.4 Analog LCM and LEM Terminations ....................................................................................................... 116
9.6.5 Networking.............................................................................................................................................. 120
9.7 MODEM/PRINTER/HLI INTERFACE ................................................................................................................... 124
9.7.1 Modem Interface ..................................................................................................................................... 124
9.7.2 Printer/Pager/HLI Interface.................................................................................................................... 125
9.8 BATTERY CALCULATIONS:............................................................................................................................... 127
9.8.1 Quiescent Current Calculation:............................................................................................................... 127
9.8.2 Alarm Current Calculation:..................................................................................................................... 127
9.8.3 Battery Capacity Requirements: .............................................................................................................. 127
9.8.4 Power Supply Capacity Requirements: .................................................................................................... 127
9.9 FIELD REPLACEMENT PARTS:........................................................................................................................... 128
9.10 FIELD MODULE CONNECTION DIAGRAMS......................................................................................................... 129
9.10.1 AZM-8 .................................................................................................................................................... 129
9.10.2 FAN Controller....................................................................................................................................... 130
9.11 ANNUNCIATOR CONNECTION ........................................................................................................................... 131
9.11.1 RS485 Comms and Power Connections.................................................................................................... 131
9.11.2 ACM-16AT (16 buttons, 32 LED’s).......................................................................................................... 132
9.11.3 ACM-32A (32 Red LED’s)....................................................................................................................... 133
9.11.4 SCS-8 (8 Fan Controls)........................................................................................................................... 134
9.11.5 LDM-32 (Expansion Relay Driver Board)................................................................................................ 135
9.11.6 LDM-R32 (32 Expansion Relays)............................................................................................................. 136
9.11.7 LCD80 Display Interface......................................................................................................................... 137
9.12 PANEL EXPANSION RELAYS ............................................................................................................................. 138
9.13 ANALOG ADDRESSABLE DEVICES .................................................................................................................... 139
9.13.1 Detector Bases........................................................................................................................................ 139
9.13.2 Isolator Base........................................................................................................................................... 140
9.13.3 Isolation Module ..................................................................................................................................... 141
9.13.4 Relay Module.......................................................................................................................................... 142
9.13.5 Control Module....................................................................................................................................... 143
9.13.6 Zone Module........................................................................................................................................... 144
9.13.7 Monitor Module ...................................................................................................................................... 145