Honeywell INTELLIGUARD 9000 - Test Modes

INTELLIGUARD 9000™
74-3047—124
d. If the device has serial numbers, verif
y
that the
proper serial number was pro
g
rammed usin
g
PRO
9000.
10.
If the volta
g
e is acceptable but the device still does not
respond while learnin
g
or durin
g
re
g
ular pollin
g
, replace
it with a new device as described in these instructions.
NOTE: Power down the whole s
y
stem
(
all ISPs, CUs and
RIPS
)
before replacin
g
a device.
Test Modes
The Test menu is accessible throu
g
h the CC2 and has three
submenus; 1. HOLD-UP Test, 2. CHIME and 3. WALK-TEST.
The Walk Test ma
y
be used to test for proper operation of an
y
s
y
stem input, but it is recommended that the Hold-up Test
menu be used for Hold-up actuators since that test
automaticall
y
performs a
Reset Detector
when the test is over.
The Chime Test verifies the chime function
(
tone on a CC2 or
KID
)
pro
g
rammed for door inputs
(
pro
g
rammed as t
y
pe 1
)
and
associated with a defined area
(
s
)
. It also verifies that the
chime is activated on the ri
g
ht CC2 or KID when a door
(
whose correspondin
g
input is pro
g
rammed for the same area
as defined for the CC2 or KID
)
is opened.
The CHIME menu is used to enable or disable the chime
function for an
y
of the ei
g
ht active areas. If the chime function
is enabled for a particular area, the points associated with that
area will activate a chime provided the
y
are pro
g
rammed as
door inputs
(
pro
g
rammed as point t
y
pe 1
)
. The chime will
sound on an
y
CC2 or KID assi
g
ned to that area when a door
is opened.
NOTE: When one of the function ke
y
s
(
TEST, MODE or
OPT
)
is pressed and a valid ID and pass code are
entered, it is not necessar
y
to exit to the Main menu,
select a different function ke
y
and then reenter
y
our
ID and pass code. You can
j
ump to an
y
of the func-
tions directl
y
b
y
pressin
g
another function ke
y
from
an
y
where in the menu structure, except in the
parameter chan
g
in
g
menus, such as in the learnin
g
process or point parameter chan
g
e menu. The fol-
lowin
g
procedures use this feature.
1. HOLD-UP Test Procedure
1.
Check to see if an
y
Hold-up points are in alarm.
2.
Make a
Reset Detectors
command if necessar
y
.
3.
From the CC2, press the
MODE
ke
y
.
4.
Enter
y
our technician ID and code number
(
00, 9999
)
.
5.
Clear the Event Lo
g
b
y
enterin
g
a
4
on the CC2 and
then pressin
g
the
ACCEPT
ke
y
.
6.
Press the
TEST
ke
y
.
HOLD-UP TEST
is displa
y
ed on
the CC2.
NOTE: Your ID and code number do not need to be reen-
tered.
7.
Press the
ACCEPT
ke
y
.
8.
Enter the test area number.
NOTE: The CC2 displa
y
will flash
HOLD-UP TEST
on the
first line of the displa
y
and the LED below the displa
y
will also flash. A beep will also be heard until step 10
is performed or a time out occurs.
(
Onl
y
the CC2
from which the test was initiated flashes and beeps.
)
9.
Walk throu
g
h the selected area of the buildin
g
(
selected
in previous step
)
and s
q
ueeze the red Hold-up actuator
buttons on each BIC-2 HU.
(
You have 7-1/2 minutes to
do the walk throu
g
h before the s
y
stem automaticall
y
ends the test. The beep rate accelerates after 7 minutes
and the CC2 displa
y
s a flashin
g
END TEST
for the last
30 seconds before revertin
g
back to the 1-HOLD-UP
TEST menu displa
y
. Two beeps are heard when the test
ends automaticall
y)
.
NOTES:
— The Hold-up actuator COM LED momentaril
y
flashes bri
g
hter when the actuator buttons are
s
q
ueezed to
g
ether to perform the test. Two beeps
are heard each time an actuator’s buttons are
s
q
ueezed.
— In HOLD-UP TEST mode, the second line of the
CC2 displa
y
is blank until an actuator’s buttons
have been s
q
ueezed. When the buttons have
been s
q
ueezed on an
y
actuator, the second line
of the CC2 displa
y
shows that the chosen BIC-2
HU is in alarm. Both lines of the CC2 flash s
y
n-
chronousl
y
. When the next Hold-up actuator is
s
q
ueezed, its identit
y
replaces that of the previ-
ousl
y
tested actuator on the second line of the
CC2 displa
y
. The format for the second line of the
CC2 displa
y
in HOLD-UP TEST mode is:
:
— The information shown in the example ma
y
differ
dependin
g
on the settin
g
s pro
g
rammed for the
point. Dependin
g
on the len
g
th of the messa
g
es,
the information ma
y
be truncated since there are
onl
y
24 characters on the second line of the dis-
pla
y
.
10.
Return to the CC2 and press the
X
ke
y
to end the test if
the time out has not expired. The CC2 displa
y
and LED
stop flashin
g
and beepin
g
.
SUCCESS!
is displa
y
ed
momentaril
y
on the CC2. This means the Test function
completed successfull
y
and not that the actuators
tested oka
y
. Refer to the Hold-up Test Event Lo
g
sec-
tion to ensure that the devices tested successfull
y
. The
I9000 s
y
stem automaticall
y
performs a
Reset Detectors
command.
11.
Press the
MODE
ke
y
.
NOTE: Your ID and code number do not need to be reen-
tered.
12.
Press
3
to select Event Lo
g
.
(
Wait a few seconds to
allow the Hold-up actuators to reset
)
.
13.
Press the
ACCEPT
ke
y
to view the Event Lo
g
.
14.
View the results of the test in the Event Lo
g
. See the
Hold-up Test Event Lo
g
section for an example of the
Lo
g
results.
15.
Repeat steps 5 throu
g
h 14 for each of the areas pro-
g
rammed at the installed site.
Area
Point
No.
Message
No. 1 Alarm
Message
No. 2
Logical
No.
A1 010 BIC-2 ALM HOLD-UP 2