Honeywell MagneW 3000 Plus - Page 45

36-KI-16-24
Page 3 of 5
Availability
MGG14ID
TABLE
V
Selection
A - Diameter Flow Range Minimum Flow Range Maximum
Millimeter Inches
In US GPM In Litres In US GPM In Litres
2.5 0.1 0.008 0.03 0.779 2.95 002 _ _ _ _ _ _ _ _ _
5.0 0.2 0.031 0.12 3.113 11.78 005 _ _ _ _ _ _ _ _ _
10 0.39 0.125 0.47 12.460 47.17 010 _ _ _ _ _ _ _ _ _
15 0.5 0.280 1.06 28.002 106.00 015 _ _ _ _ _ _ _ _ _
25 1.0 0.779 2.95 77.931 295.00 025 _ _ _ _ _ _ _ _ _
40 1.5 1.990 7.53 199.011 753.34 040 _ _ _ _ _ _ _ _ _
50 2.0 3.113 11.78 311.285 1178.34 050 _ _ _ _ _ _ _ _ _
65 2.5 5.239 19.83 523.945 1983.34 065 _ _ _ _ _ _ _ _ _
80 3.0 7.969 30.17 796.924 3016.68 080 _ _ _ _ _ _ _ _ _
100 4.0 12.46 47.17 1246.02 4716.68 100 _ _ _ _ _ _ _ _ _
125 5.0 19.46 73.67 1946.08 7366.69 125 _ _ _ _ _ _ _ _ _
150 6.0 28.00 106.00 2800.24 10600.04 150 _ _ _ _ _ _ _ _ _
200 8.0 49.80 188.50 4979.68 18850.07
200 _ _ _ _ _ _ _ _ _
B - Liner
PFA _ _ _ P _ _ _ _ _ _ _ _
*
Polyurethane Rubber (25 to 200mm only)
_ _ _ Q _ _ _ _ _ _ _ _
d
C - Pipe Connection
Wafer JIS10K _ _ _ _ 11 _ _ _ _ _ _
j
Wafer JIS20K _ _ _ _ 12 _ _ _ _ _ _ j
Wafer JIS30K _ _ _ _ 13 _ _ _ _ _ _ j
Wafer JIS10/20K for 10mm flange _ _ _ _ 14 _ _ _ _ _ _ g
Wafer JIS30K for 10mm flange _ _ _ _ 15 _ _ _ _ _ _ g
Wafer ANSI150 _ _ _ _ 21 _ _ _ _ _ _
*
Wafer ANSI300 _ _ _ _ 22 _ _ _ _ _ _
Wafer JIS G3451 F12 (diameter 80mm or larger) _ _ _ _ 31 _ _ _ _ _ _
h
Wafer DIN PN10 _ _ _ _ 41 _ _ _ _ _ _ j
Wafer DIN PN16 _ _ _ _ 42 _ _ _ _ _ _ j
Wafer DIN PN25 _ _ _ _ 43 _ _ _ _ _ _ j
Wafer DIN PN40 _ _ _ _ 44 _ _ _ _ _ _ j
Wafer DIN PN10/16/25/40 for 10mm flange _ _ _ _ 45 _ _ _ _ _ _ g
Wafer JPI150 _ _ _ _ 61 _ _ _ _ _ _
Wafer JPI300
_ _ _ _ 62 _ _ _ _ _ _
D - Electrodes
SUS316L _ _ _ _ _ _ L _ _ _ _ _
*
Hastelloy C (with Teflon PFA only) _ _ _ _ _ _ C _ _ _ _ _ c
Titanium _ _ _ _ _ _ K _ _ _ _ _
Zirconium (with Teflon PFA only) _ _ _ _ _ _ H _ _ _ _ _ c
Tantalum (with Teflon PFA only) _ _ _ _ _ _ T _ _ _ _ _ c
Tungsten Carbide (only for size 10mm and above) _ _ _ _ _ _ W _ _ _ _ _ e
Platinum-Iridium (with Teflon PFA only) _ _ _ _ _ _ P _ _ _ _ _ c
Alloy 20 (with Teflon PFA only) _ _ _ _ _ _ A _ _ _ _ _ c
Hastelloy B (with Teflon PFA only) _ _ _ _ _ _ B _ _ _ _ _ c
SUS304 (with Teflon PFA only) _ _ _ _ _ _ E _ _ _ _ _ c
Monel (with Teflon PFA only) _ _ _ _ _ _ M _ _ _ _ _ c
Nickel (with Teflon PFA 15-200mm only) _ _ _ _ _ _ N _ _ _ _ _ f
SUS316L Protruded Tip (with Teflon PFA 15-200mm only) _ _ _ _ _ _ 1 _ _ _ _ _ f
SUS316L for Alumina with Flat Tip (with Teflon PFA 15-200mm only) _ _ _ _ _ _ 2 _ _ _ _ _ f
SUS316L for Alumina with Pointed Tip (with Teflon PFA 15-200mm only)
_ _ _ _ _ _ 3 _ _ _ _ _
f