Why does my Honeywell TP70 Dehumidifier run constantly and not stop?
Your dehumidifier might be running constantly because the area you're trying to dehumidify is too large for its capacity. Consider adding another dehumidifier for larger spaces. Also, check if any doors or windows are open, letting in new moisture. Make sure to keep them closed and tightly sealed.
Why is there frost on the coils of my Honeywell TP70?
If you recently turned on your dehumidifier in a room with low temperatures (usually below 41°F or 5°C), frost may appear on the coils. This is normal and should disappear within an hour or so after switching the dehumidifier off.
How to fix a Honeywell TP70 Dehumidifier that does not start?
First, check if there is electricity and that the power cord is properly plugged in; remove and reconnect it. Also, check the safety switch on the electrical plug and reset it, waiting three minutes. If it still doesn't start, ensure the water tank is correctly positioned, as the unit won't operate without it being secure.
What to do if my Honeywell Dehumidifier is running but the humidity level isn't decreasing?
Several factors could be at play. Ensure the humidity level setting isn't too high. Close any open doors or windows to prevent new moisture from entering. Eliminate other humidity sources in the room. Make sure the room temperature is between 41°F (5°C) and 89°F (32°C). Clean the dust filter if it's dirty or blocked, and remove any blockages from the air outlet or intake.
How to fix Honeywell TP70 Dehumidifier when water is on the floor?
If you find water on the floor, check the connections between the garden hose/drain hose and the drain outlet on the unit to make sure they are not loose. If you're using the water tank, disconnect the hose and replace the rubber stopper and drain cap. Refer to the Continuous Water Drainage section for more details.
How to fix Honeywell TP70 if it is not draining with continuous drain?
If the water isn't draining out of the tube when using continuous drain, try raising the front of the dehumidifier by ½ to 1 inch (1.27 cm to 2.54 cm) from the floor. This helps the water drain out the back hose instead of collecting in the bucket.
What to do if the 'Water Tank Full' light is on and my Honeywell Dehumidifier is beeping?
This usually means the water tank is full or not correctly positioned. First, empty the water tank. If that doesn't solve it, make sure the water tank is correctly positioned in the unit. The unit won't work if the tank isn't secure.
Why is my Honeywell TP70 Dehumidifier blowing cold air?
The top air vent distributes air into the room. The air temperature from the vent can change based on the room and other conditions, which is normal, so no action is required.
Why is my Honeywell Dehumidifier making noise?
The fan creates sounds during operation, which is a normal part of how the dehumidifier works.
What does P1 mean on my Honeywell TP70 Dehumidifier?
The P1 error code indicates that the water tank has been pulled out. To fix this, correctly position the water tank back into the unit. The unit will not operate until the water tank is secure.
General| Brand | Honeywell |
|---|---|
| Model | TP70 |
| Category | Dehumidifier |
| Language | English |
Essential safety guidelines for operating electrical appliances to prevent hazards.
Instructions on proper handling, storage, and use by persons with reduced capabilities.
Step-by-step guide to safely empty the water collected in the dehumidifier's tank.
Procedures for maintaining the dehumidifier's cleanliness and filter efficiency.
Solutions for common problems when the dehumidifier fails to power on or start.
Addressing issues where the dehumidifier is running but not reducing humidity.
Solutions for continuous running, water tank full indicators, and associated alerts.
Explanation of error codes (P1, EH, E1/E2, E3) and recommended actions.
To Next Page