)
Operating Instructions.
Important Safety Instructions.
Before using the vacuum cleaner, always read the operating
instructions and keep them readily available.
Purpose and Intended Use.
The vacuum cleaner described in this operating manual is
suitable for private use, e.g. household, hobby workshop, car
cleaning and sucking up dust and liquids.
Name and Parts Location.
1. Castor wheels
2. Drum
3. Latch
4. Cord Storage
5. Motor housing
6. ON/OFF Switch
7. Handle
8. Flexi hose
9. Extension tube 10
10. Carpet / Floor nozzle
11. Furniture brush
12. Crevice tool 1
13. Blow outlet
I? ~12 ~"
The followingmaterials shouldnot be picked up by the
vacuumcleaner.
13
5
/3
· Hazardous dust
· Hot materials (burningcigarettes,hot ash, etc.)
· Flammable, explosiveor aggressive liquids(e.g. petrol,
solvents, acids,alkalis,etc.)
· Flammable or explosive dust (e.g. magnesiumor
aluminiumdust,etc.)
BeforeStart-up.
. Ensure that the voltage shown on the rating plate
correspondsto the voltageof the localMainspowersupply.
· It is recommended that the vacuum cleaner should be
connectedviaa residentialcurrentcircuit breaker.
· Inspectthe powercordregularlyto detect signs of damage,
e.g. cracks or ageing. A damaged power cord must be
replaced by an authorisedperson. Never use th-evacuum
cleaner ifthe filteris damaged.
1.
Operating your HooverHWD020Wet/Dry vacuum cleaner:
I. Unwind the power supply cord ITomthe cord storage
andplug intothe power supplysocketoutlet.
2. Switch the vacuum cleaner ON by depressing the
ON/OFFswitch.
3. A suction regulator is located on the hose handle.
To activate simply slide the regulator open to reduce
the level of suction required. The suctionregulator
shouldbekept in the closedposition.
4. The suctionpower will reduce and stop as the drum
fills up. It is recommendedto empty the drum on a
regularbasis.
5. To switchthe vacuumOFFdepressthe ON/OFFswitch
againandthenremoveITomthe mainspowersupply.
PowerCord
1.
3.
2.
Pickingup Liquids.
Before liquids are picked up, always remove the filter bag.
If foam developsor liquid emerges, stop work immediately
andemptythe drum.
~
~J
~-~~
#~
2.
Blow Function.
1. Unwind the power supply cord ITomthe cord storage.
2. Attach the flexi hose to the blow outlet and attach the
desired nozzle to the flexi hose.
3. Switch the vacuum cleaner ON by depressing the
ON/OFF switch.
4. To switch the vacuum cleaner OFF depress the
ON/OFF switch again and then remove ITomthe mains
power supply.
1.
~!
20~
'oB,
Maintenance, Cleaning and Repair.
1. Disconnect the plug ITom the mains power supply
before cleaning.
2. Take care when emptying the drum, as when fullit
could weighup to 24 kg.
3. Releasethe two latcheslocatedon the drum in orderto
removethe motorhousing.
4. Emptythe drumusingthe handle grip located on the
undersideofthe drum.Cleanwith a warm moistcloth
and buff dry. Do not use harsh abrasivesor other
cleaningaidsto cleanthe vacuumcleaner.
5. Clean the filter periodicallyby gently beating it over
a rubbish bin. If cleaning is not done the suction
power of the vacuumwill decrease.
6. After cleaning the vacuum cleaner, placethe motor
housing on to the drumand securethe twolatches
back intoplace.For correctassemblyof motorhousing
to drum,ensurethat the vacuuminletandthe blower
outlet lineup vertically.
7. Never spraywater overthe upper sectionofthe vacuum
cleaner.
3.
To Previous Page
Loading...
Need help?
General
