HP Synergy 480 Gen10 - Installation Overview and Procedure

124 pages

To Next Page

To Previous Page

Installation overviewInstallation overview

Use this section and the following procedure to install the HPE Synergy 480 Gen10 Compute Module in a frame for the first time.

ProcedureProcedure

1. Install supported options for the compute module.

2. Install the compute module.

3. Complete the compute module configuration.

Installation overview 46

Main Page

Table of Contents3
Component Identification6
Front Panel Components7
Serial Label Pull Tab Information8
Front Panel Leds and Buttons9
Drive Numbering11
Smart Carrier (SC) Drive LED Definitions12
SFF Flash Adapter Components and LED Definitions13
Smart Carrier Nvme (SCN) Drive LED Definitions14
System Board Components16
System Maintenance Switch17
Processor, Heatsink, and Socket Components18
Mezzanine Connector Definitions19
DIMM Slot Locations20
DIMM Label Identification21
NVDIMM Identification23
NVDIMM 2D Data Matrix Barcode24
NVDIMM LED Identification25
NVDIMM-N LED Combinations26
NVDIMM Function LED Patterns27
Intel Optane Persistent Memory 100 Series for HPE Label Identification28
Enterprise Midline USB29
Leds30
Component and LED Identification for HPE Synergy Hardware31
Operations32
Powering up the Compute Module33
Powering down the Compute Module34
Removing the Drive Blank35
Removing the Compute Module36
Removing the Compute Module End Cap37
Removing the Access Panel38
Removing the DIMM Baffle39
Removing the Front Panel/Drive Cage Assembly40
Installing the Compute Module End Cap41
Installing the Access Panel42
Installing the DIMM Baffles43
Installing the Front Panel/Drive Cage Assembly44
Setup45
Installation Overview46
Installing the Compute Module47
Completing the Configuration49
Hardware Options Installation50
Introduction51
Installing SAS, SATA, or Solid State Drives52
Installing the SFF Flash Adapter Option53
Installing the M.2 SSD Flash Drive and Adapter Board54
Installing the Controller Option56
Installing Mezzanine Card Options57
Installing the P416Ie-M Controller Mezzanine Option58
HPE Smart Storage Battery60
HPE Smart Storage Hybrid Capacitor61
Minimum Firmware Versions62
Installing the Energy Pack Option63
Memory Options65
DIMM and NVDIMM Population Information66
DIMM-Processor Compatibility67
HPE Smartmemory Speed Information68
Installing a DIMM69
HPE 16GB NVDIMM Option70
Server Requirements for NVDIMM Support71
Installing an NVDIMM72
Configuring the Compute Module for Nvdimms74
NVDIMM Sanitization75
NVDIMM Relocation Guidelines76
Intel Optane Persistent Memory 100 Series for HPE77
Persistent Memory Module-Processor Compatibility78
Persistent Memory Module Population Information79
System Requirements for Persistent Memory Module Support80
Installing Persistent Memory Modules81
Configuring the Compute Module for Intel Optane Persistent Memory 100 Series for HPE82
Persistent Memory Module Relocation Guidelines84
Migrating a Persistent Memory Module86
Installing the Processor Heatsink Option87
HPE Trusted Platform Module 2.0 Gen10 Option90
Overview91
HPE Trusted Platform Module 2.0 Guidelines92
Installing and Enabling the HPE TPM 2.0 Gen10 Option93
Installing the Trusted Platform Module Board94
Preparing the Compute Module for Installation95
Installing the TPM Board and Cover96
Preparing the Compute Module for Operation98
Enabling the Trusted Platform Module99
Enabling the Trusted Platform Module as TPM 2.0100
Retaining the Bitlocker Recovery Key/Password102
Cabling103
Cabling Resources104
Energy Pack Option Cabling105
P416Ie-M Smart Array Controller Cabling106
Removing and Replacing the System Battery107
Electrostatic Discharge108
Preventing Electrostatic Discharge109
Grounding Methods to Prevent Electrostatic Discharge110
Specifications111
Compute Module Environmental Specifications112
Compute Module Physical Specifications113
HPE Synergy Documentation Resources114
HPE Synergy Firmware Update Resources115
HPE Synergy Documentation Map116
Websites117
Support and Other Resources118
Accessing Hewlett Packard Enterprise Support119
Accessing Updates120
Remote Support121
Warranty Information122
Regulatory Information123
Documentation Feedback124

HP Synergy 480 Gen10 - Installation Overview and Procedure

Table of Contents

Related product manuals