EasyManua.ls Logo

Huawei quidway s7700 - Page 96

Huawei quidway s7700
833 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
l IP addresses of the interfaces on the two ends of the GRE tunnel
Procedure
Step 1 Assign the IP address to each interface.
<Quidway> system-view
[Quidway] sysname SwitchA
[SwitchA] vlan batch 10 20
[SwitchA] interface gigabitethernet 1/0/0
[SwitchA-GigabitEthernet1/0/0] port hybrid pvid vlan 10
[SwitchA-GigabitEthernet1/0/0] port hybrid untagged vlan 10
[SwitchA-GigabitEthernet1/0/0] quit
[SwitchA] interface gigabitethernet 2/0/0
[SwitchA-GigabitEthernet2/0/0] port hybrid pvid vlan 20
[SwitchA-GigabitEthernet2/0/0] port hybrid untagged vlan 20
[SwitchA-GigabitEthernet2/0/0] quit
[SwitchA] interface vlanif 10
[SwitchA-Vlanif10] ip address 10.1.1.2 24
[SwitchA-Vlanif10] quit
[SwitchA] interface vlanif 20
[SwitchA-Vlanif20] ip address 20.1.1.1 24
[SwitchA-Vlanif20] quit
The configurations of Switch B and Switch C are similar to the configuration of Switch A, and
are not mentioned here.
Step 2 Configure OSPF process 1 between SwitchA, SwitchB, and SwitchC.
# Configure SwitchA.
[SwitchA] ospf 1
[SwitchA-ospf-1] area 0
[SwitchA-ospf-1-area-0.0.0.0] network 20.1.1.0 0.0.0.255
[SwitchA-ospf-1-area-0.0.0.0] quit
[SwitchA-ospf-1] quit
# Configure SwitchB.
[SwitchB] ospf 1
[SwitchB-ospf-1] area 0
[SwitchB-ospf-1-area-0.0.0.0] network 20.1.1.0 0.0.0.255
[SwitchB-ospf-1-area-0.0.0.0] network 30.1.1.0 0.0.0.255
[SwitchB-ospf-1-area-0.0.0.0] quit
[SwitchB-ospf-1] quit
# Configure SwitchC.
[SwitchC] ospf 1
[SwitchC-ospf-1] area 0
[SwitchC-ospf-1-area-0.0.0.0] network 30.1.1.0 0.0.0.255
[SwitchC-ospf-1-area-0.0.0.0] quit
[SwitchC-ospf-1] quit
# Run the display ip routing-table command on Switch A and Switch C. You can find that they
learn the OSPF routes destined for the network segment of the peer.
Step 3 Configure the tunnel interface.
The configuration procedure is the same as that in 2.7.1 Example for Configuring Static Routes
on the GRE Tunnel.
Step 4 Configure the OSPF protocol on the tunnel interfaces.
# Configure Switch A.
[SwitchA] ospf 2
[SwitchA-ospf-2] area 0
Quidway S7700 Smart Routing Switch
Configuration Guide - VPN 2 GRE Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
81

Table of Contents

Other manuals for Huawei quidway s7700

Related product manuals