Husqvarna 917.289630 - Page 33

DRIVE
TRACTOR - - MODEL NUMBER YTH22V46 (289630)
KEY PART
NO. NO.
1
2 532 12 35-83
15 819 13 13-16
17 532 41 38-78
26 532 19 98-79
29 532 40 38-06
33 812 00 00-01
35 532 19 95-91
42 532 12 48-72
49 872 11 06-14
50 532 19 43-27
51 873 90 08-00
52 532 19 43-28
58 532 13 09-89
84 532 19 78-85
73 874 49 05-40
80 532 41 00-24
92 874 76 05-20
99 532 41 57-42
116 873 90 05-00
125 817 00 05-12
143 817 49 05-08
153 532 12 47-88
159 876 02 04-12
180 532 18 94-84
181 532 10 57-09
183 532 40 10-34
186 532 42 91-84
167 532 40 52-57
170 532 41 34-30
183 532 13 70-57
KEY PART
DESCRIPTION NO. NO. DESCRIPTION
Transaxle, Tufftorq K48BT 184 532 40 31-18
Key Square 185 872 11 08-22
Washer 13/32 x 13/18 x 18 Ga. 188 532 19 43-21
Spring, Brake 187 819 13 32-10
Spring Return Cruise 188 532 19 43-23
Rod, Brake 189 5321943-17
Ring E 190 532 19 43-18
Rod, Brake, Park 205 532 12 17-48
Cover, Foot Pedal 206 532 19 78-67
Bolt 207 532 19 78-68
Pulley Idler Flat 208 532 19 78-89
Lock Nut 3/8-16 209 532 19 95-92
Idler V-Groove 910" Offset 210 532 40 09-80
V-Belt, Drive 211 532 12 01-83
Shaft Asm. Pedal Brake Control 213 532 40 31-19
Bolt Hex 5/16-18 Gr. 5 214 532 42 12-63
Strap Torque 215 532 40 17-23
Bolt FinHex5/18-18uncxl.25 216 5321961-31
Rod Spring Bypass 221 532 40 31-87
Nut Lock Hex Flange 5/18-18 222 879 21 20-10
Screw 5/16-18 x 3/4 225 532 40 33-19
Screw 5/18-18 x 1/2 228 532 40 15-84
Retainer Spring 1" 227 817 49 05-12
Pin Cotter 1/8 x 3/4 230 532 18 89-67
Retainer Clip 231 532 40 72-87
Spring, Return, Clutch
Rod Control
Nut Push
Latch Brake Parking
Keeper V-Idler
Spacer Axle
Handle Parking Brake
Bolt
Spacer Retainer
Washer
Link Clutch Ground Drive
Bellcrank Ground Drive
Keeper Bellcrank Ground Drive
Washer 25/32 x 1-5/8 x 16 Ga.
Bracket Mount Latch Cruise
Latch Control Cruise
Gear Sector Control Cruise
Rod Control Cruise
Rocker Asm. Pedal Control
Bearing Nylon
Knob Control Cruise
Pedal Forward Pad
Pedal Reverse
Bracket Pulley Idler
Retainer Spring Clip Handle
Washer 21/32 x 1-1/4 10 Ga.
Keeper Belt Transaxle
Bracket Mount Torque
Screw Thdrol 5/18-18 x 3/4
Washer Harden .793 x 1.637 x 060
Idler V-Groove 1.888" Offset
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
33