3-7. V-cable Wrap Test Connections ..................... 3-28
3-8. Channel Interface-in Wrap Test Connections ............. 3-29
3-9. All Cables Wrap Test Connections ................... 3-30
3-10. Channel Interface-out Wrap Test Connections ............. 3-31
3-11. Select/Bypass Switch on V-Cable .................... 3-33
3-12. Cabling to IBM multiaccess enclosure at the End of Channel .... 3-34
3-13. Cabling to IBM multiaccess enclosure in the Middle of the Channel 3-35
3-14. Interconnected V-cables . . . . . . . . . . . . . . . . . . . . . . . . . 3-36
3-15. Standard Channel Connection ...................... 3-38
3-16. Two Adapters Attached to One Channel ................ 3-38
3-17. Three Adapters Attached to One Channel ............... 3-39
3-18. IBM multiaccess enclosure Parallel Channel Adapter on a Channel
with a 3172 Connected to a Channel Interface Assembly ...... 3-39
3-19. Select/Bypass Switch on V-Cable .................... 3-42
4-1. Service Processor Customization ..................... 4-6
4-2. Service LAN addresses ........................... 4-6
4-3. Power Supply, System Card, SAC card, and Adapter Card LEDs . 4-11
4-4. MAE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
4-5. MAE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
4-6. MAE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
4-7. MAE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
4-8. MAE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
4-9. MAE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
4-10. Install Multiaccess Enclosure ....................... 4-20
4-11. Service LAN Addresses .......................... 4-21
4-12. SP Customization Message ....................... 4-21
4-13. SP Customization Completed ...................... 4-21
4-14. Service Processor Customization .................... 4-28
4-15. Service LAN addresses .......................... 4-28
4-16. Removal of the Multiaccess Enclosure ................. 4-52
5-1. System Management Utilities ....................... 5-4
5-2. System Configuration Information ..................... 5-6
5-3. Boot Sequence Selection .......................... 5-7
5-4. Current Boot Sequence ........................... 5-8
5-5. Test Selection Panel ............................ 5-9
5-6. Utilities Selection Panel .......................... 5-10
5-7. Set Power-On Password Panel ..................... 5-11
5-8. Set Supervisory Password Panel .................... 5-12
5-9. Unattended Start Mode Changed (Enabled) Panel .......... 5-13
5-10. Unattended Start Mode Changed (Disabled) Panel .......... 5-14
5-11. Remove Supervisory Password Panel ................. 5-15
5-12. System Firmware Update Panel ..................... 5-16
5-13. Example of Error Log Panel ....................... 5-23
5-14. View or Set Vital Product Data Panel .................. 5-24
5-15. Manipulate Dead Man Timer Panel ................... 5-27
5-16. Setup Remote Initial Program Load Panel ............... 5-28
5-17. TFTP Software Selection ......................... 5-32
5-18. Install Multiaccess Enclosure ....................... 5-37
5-19. Service LAN Addresses .......................... 5-38
5-20. SP Customization Message ....................... 5-38
5-21. SP Customization Completed ...................... 5-38
5-22. Operational Diagnostics Main Menu ................... 5-43
5-23. Sample of Device List Panel Showing Interfaces ........... 5-44
5-24. Device Status and Control Panel (Device Disabled) ......... 5-45
xii 3746-9X0: MAE Installation and Maintenance
To Next Page
Loading...
