IBM 900 - Page 9

How to Reset the Multiaccess Enclosure ................... E-2
Migrating to a New Code level ......................... E-2
Installing a New User Module .......................... E-3
Other Change Management Functions ..................... E-4
Describe Load Images ............................ E-4
Disable Dumping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-4
Enable Dumping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-4
Erase Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-4
Using the Copy Command ............................ E-5
Configuring the MAE via CCM ........................... E-6
Activate MAE Configuration Via CCM ....................... E-14
Appendix F. Common Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1
LED States / Adapter Status ............................ F-1
The Firmware Interface ............................... F-1
Command Line Interface .............................. F-1
Displaying List of Configured Interfaces ..................... F-1
Displaying the Operational State of the Interfaces ............... F-2
Verifying Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-2
Viewing Vital Software Data ............................ F-2
Viewing Vital Hardware Data ........................... F-3
Adding/Removing an Adapter Using CCM .................... F-3
Suspend Traffic on an Adapter Port ....................... F-3
Resume Traffic on an Adapter Port ........................ F-3
Up-to-Date multiaccess enclosure Information ................. F-4
Disabling Interfaces that Have WAN Reroute Enabled ............. F-4
Enabling WAN Reroute after You Have Disabled it ............... F-5
Spare Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-5
Appendix G. Hardware Error Codes ...................... G-1
Appendix H. Parts Listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-1
Assembly 1: Final Assembly, Multiaccess Enclosure ............ H-2
Appendix I. Multiaccess Enclosure Cables ................... I-1
Cables Between the Multiaccess Enclosure, 3746 Models 900/950 and
Service Processor (based on 6275) ....................... I-1
Cables Between the Multiaccess Enclosure, 3746 Models 900/950 and
Service Processor (based on 7585) ....................... I-2
Cable From the Multiaccess Enclosure Lan Adapter to the 8228 ....... I-3
Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-3
Cable from the Multiaccess Enclosure System Card PCMCIA Token-Ring
Adapter to Service Processor .......................... I-4
Interchange Circuits for the Cable between the Multiaccess Enclosure and
the Service Processor ............................. I-4
Balun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-5
Balun Pin Assignment .............................. I-5
Cable from the Multiaccess Enclosure EIA-232 Connector to the Service
Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-6
Interchange Circuits for the Cable between the Multiaccess Enclosure and
the Service Processor ............................. I-6
Adapter Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-7
Cable From the Service Processor or Network Node Processor to the 8228 I-8
Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-8
Contents vii